Panasonic SC-ZT2 warranty Adjusting sound quality, Adjusting the volume balance of front speakers

Adjusting the surround speaker output using the test signal

You can make this setting when using the surround speakers. You can adjust the surround speaker volume by outputting the test signal.

1. Press [TEST] to output the test signal.

Speaker display

L : Front left, R : Front right,

RS : Surround right, LS : Surround left

•The test signal is output from one speaker at a time for two seconds in the following order.

TEST L p TEST R p TEST RS p TEST LS

2.Press [VOL +, –] to adjust the volumes of front speakers to the normal listening

level.

Adjustment range: 0 (Min) to 50 (Max)

3.Press [CH] to select surround speakers for adjustment.

4.Press [SPEAKER LEVEL +, –] to adjust

each speaker’s output level.

Adjustment range: RS, LS : –10to +10

•The test signal comes from the speaker being adjusted.

•The test signal is output again in the above order 2 seconds after adjustment.

„Repeat steps 3 and 4 to adjust the level of each speaker.

5. Press [TEST] to stop the test signal.

Note

•You can check the audio output of the front speakers.

(➜ page 14) (When the surround speakers are not used, only “TEST L ” and “TEST R ” are displayed and the test signal is output alternately.)

•To adjust the volume balance of left and right front speakers, see “Adjusting the volume balance of front speakers”

(➜ right).

•Even if you adjust each channel level in this adjustment, each

channel level setting in each SFC mode (➜ page 17) does not change.

•When you make this adjustment while using the front speakers only, Dolby Virtual Speaker functions. When playing 2-channel sources, Dolby Pro Logic also works in conjunction. (➜ page 17)

•To adjust the bass volume, do not output the test signal for adjustment. (➜ page 20)

„Setup menu items

✽“BASS”	✽“TREBLE”	✽“BALANCE”
“SPEAKERS”	✽“DISTANCE”	“7.1CH VS”
	✽“STB AUDIO”
“HDMI”		“SOUND DLY”
“DUAL PRG”	“DRCOMP”	“ATTENUATOR”
“REMOTE”	“INPUT MODE”	“RESET”

“EXIT”

•✽ appears only when audio adjustment can be made.

•Select “EXIT ” and press [OK] to finish the setup mode.

Adjusting sound quality

You can adjust the level of bass and treble.

This setting is effective only when you perform stereo playback of 2-channel analog and PCM signals (during Dolby Virtual Speaker and Dolby Pro Logic is off).

This setting is not displayed in other conditions. Be sure to make this setting in the above condition.

1. Press and hold [–SETUP, OFF] for about

2 seconds.

The setting items are displayed. (➜ above)

2.Press [w][q] to select “BASS ” or “TREBLE ” and press [OK].

3.Press [e][r] for adjustment, and press

[OK].

Adjustment range: –6to +6

Factory setting: 0

4.Press [ RETURN] several times to select “EXIT ” and press [OK] to finish the setting.

Adjusting the volume balance of front speakers

You can adjust the balance of the front speakers.

1. Press and hold [–SETUP, OFF] for about

2 seconds.

The setting items are displayed. (➜ above)

2.Press [w][q] to select “BALANCE ” and press [OK].

3.Press [w][q] for adjustment, and press

[OK].

L : Front left

R : Front right

Move the bar to left and right on the display to adjust.

•As the bar gets closer to “L ”, the sound moves to left front.

•As the bar gets closer to “R ”, the sound moves to right front.

4.Press [ RETURN] several times to select “EXIT ” and press [OK] to finish the setting.

Note

•The bar indication is approximate.

•When using headphones, you cannot adjust the volume balance.

Functions and settings

Play

21

VQT2R70