Atlas 240 Series manual Specifications, Troubleshooting Guide

Page 5

SPECIFICATIONS

Range . . . . . . . Up to 70 ft. (21 m); 100 ft. (30.5m)withRangeBoost.[varies with surrounding temperature]

Sensing Angle. . . . Up to 240°

Electrical Load. . . . Up to 300 Watt Maximum In- candescent [Up to 150 Watt maximum each bulb holder.]

Power Requirements. 120 VAC, 60 Hz

Replacement Lamp. . Up to 150Watt Maximum PAR38 Incandescent or Halogen (Not CFL) Bulbs.

Operating Modes. . . TEST, AUTO and MANUAL

MODE

Time Delay . . . . . 1, 5, 20 minutes

Dual Light Level. . . 3, 6 hours, Dusk-to-Dawn

Atlas Lighting Products, Inc. reserves the right to dis- continue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold.

TROUBLESHOOTING GUIDE

If you experience a problem with your Light Control, first follow this guide. For additional assistance write to:

Atlas Lighting Products, Inc. • Customer Service Department • P.O. Box 2348 • Burlington, NC 27216

SYMPTOM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

Lights will not come

1.

Light switch is turned off.

1.

Turn light switch on.

on.

2.

Flood lamp is loose or burned out.

2.

Check flood lamp and replace if burned out.

 

3.

Fuse is blown or circuit breaker is turned off.

3.

Replace fuse or turn circuit breaker on.

 

4.

Daylight turn-off is in effect.

4.

Recheck after dark.

 

5.

Incorrect circuit wiring, if this is a new installation.

5.

Verify wiring is correct.

 

6.

Light control aimed in wrong direction.

6.

Re-aim light control to cover desired area.

 

 

 

 

 

Lights come on in day-

1.

Light control may be installed in a relatively dark

1.

The fixture is operating normally under these condi-

light.

 

location.

 

tions.

 

2.

Light control is in TEST.

2.

Set control switch to 1, 5, or 10 minutes.

 

 

 

 

 

Lights come on for no

1.

Light control may be sensing small animals or auto-

1.

Re-aim light control.

apparent reason.

 

mobile traffic.

 

 

 

2.

Range is set too high.

2.

Reduce range.

 

3.

Dual Light Level is on.

3.

The fixture is operating normally under these condi-

 

 

 

 

tions.

 

 

 

Lights turn off too late in

Light control may be installed in a relatively dark loca-

Relocate light control, or use 3 hr. or 6 hr. setting.

Dusk-to-Dawn setting.

tion.

 

 

 

 

 

 

 

Lights stay on continu-

1.

A flood lamp is positioned too close to the light control

1.

Reposition the flood lamp away from the light control

ously.

 

or pointed at nearby objects that cause heat to trigger

 

or nearby objects.

 

 

the light control.

 

 

 

2.

The light control may be picking up a heat source

2.

Reduce range.

 

 

like an air vent, dryer vent, or brightly painted, heat-

 

 

 

 

reflective surface.

 

 

 

3.

Light control is in manual mode.

3.

Switch light control to AUTO.

 

 

 

 

 

Lights flash on and off.

1.

Heat or light from the flood lamps may be turning the

1.

Reposition the flood lamp away from the light con-

 

 

light control on and off.

 

trol.

 

2.

Heat being reflected from other objects may be turn-

2.

Reposition light control.

 

 

ing the light control on and off.

 

 

 

3.

Light control is in the TEST mode and warming up.

3.

Flashing is normal under these conditions.

 

4.

Light may be leaking through the flood lamp reflec-

4.

Replace the flood lamps with new high quality PAR

 

 

tors.

 

38 lamps. (Make sure the metal lamp protectors are

 

 

 

 

installed).

 

 

 

Lights flash once, then

Light control is detecting its own lights.

Reposition flood lamps to keep area below the light

stay off in manual

 

 

control relatively dark.

mode.

 

 

 

 

598-1094-04

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Requirements FeaturesOperation Mode Switching Summary InstallationDual Light Level Timer Wall MountMounting Black to White to Strap Junction box ground wire to green ground screw on fixtureTurn on the circuit breaker and light switch Test and AdjustmentBottom of Sensor Avoid aiming the control atTroubleshooting Guide SpecificationsFive Year Limited Warranty 598-1094-04 598-1094-04

240 Series specifications

The Atlas 240 Series is a groundbreaking advancement in the field of robotics, specifically designed to meet the demands of various industries including manufacturing, logistics, and healthcare. These state-of-the-art robots are engineered to enhance efficiency, improve productivity, and ensure safety in various environments.

One of the primary features of the Atlas 240 Series is its advanced mobility. With a bipedal design, these robots can navigate complex terrains that are often challenging for traditional machinery. The sophisticated joint articulation allows for a wide range of motion, enabling the Atlas 240 to perform tasks that require precision and adaptability. Its robust construction ensures stability and reliability, even in fast-paced and dynamic settings.

The integration of cutting-edge technologies is another hallmark of the Atlas 240 Series. Equipped with AI-driven algorithms, the robots can learn and adapt to different activities and environments over time. The real-time data processing capabilities allow them to respond to changes quickly and efficiently, making them ideal for roles that demand quick decision-making.

In terms of communication, the Atlas 240 Series utilizes advanced IoT connectivity, enabling seamless integration into existing systems. This facilitates coordination with other machines and human operators, enhancing overall workflow and productivity. Moreover, the robots are designed with user-friendly interfaces, allowing operators to easily program and control them, even without a deep technical background.

Safety is a paramount concern in any operational environment. The Atlas 240 is equipped with multiple sensors and safety protocols that ensure safe interaction with humans and other machines. These include obstacle detection and avoidance systems that prevent accidents and enhance operational safety.

The Atlas 240 Series is also designed to be highly versatile. It comes with interchangeable tools and attachments, allowing it to perform a variety of tasks, from assembly line work to logistics support. This flexibility makes it an invaluable asset across different sectors.

With its combination of advanced mobility, intelligent technologies, seamless connectivity, and safety features, the Atlas 240 Series stands out as a leading solution for modern automation challenges. As industries continue to evolve, the Atlas 240 is poised to play a crucial role in shaping the future of work.
Top Page Image Contents