3 | INSTALLATION | NOTE: Use thread sealant on all threaded connections. |
1
Dia. HOLE
FOR HAND
Drop the SLEEVE (1) into the hole in the mounting deck. |
|
|
|
|
Assemble the WASHER (2) and LOCKNUT (3) to the SLEEVE (1) and | #8 SCREWS | |||
tighten securely. |
|
|
|
|
For copper water tube installations, make two 4" long adapter nipples |
| |||
FITTING |
| |||
( 1/2" Male NPT x 1/2" CWT ). Thread nipples into the inlet and tub | MOUNTING |
| ||
outlet of the DIVERTER BODY. Tighten connections securely. Do Not Solder | SURFACE |
|
|
|
| ||||
these Connections on the DIVERTER BODY. Damage may occur. |
|
|
|
|
|
|
|
| |
9
SHOWER
2
Thread HOSE (4) into the SHOWER CONNECTION (5) of the DIVERTER BODY (6) and tighten securely. Check with local plumbing codes for backflow prevention requirements. Install a backflow prevention device if required.
Assemble MOUNTING NUT (7) and WASHER (8) onto DIVERTER BODY (6).
Insert the DIVERTER BODY (6) through the mounting deck from below.
|
|
| Assemble the VALVE LOCK RING (9) so it is flush with the top of |
|
| VALVE LOCK | ||||||||||||
|
|
| the DIVERTER BODY (6). |
|
| RING FLUSH WITH | ||||||||||||
|
|
| Position the DIVERTER BODY (6) as required and |
|
|
|
|
|
|
|
|
|
| TOP OF THREADS ON | ||||
|
|
|
|
|
|
|
|
|
|
|
| VALVE SHANK | ||||||
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
| tighten the MOUNTING NUT (7) securely. |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| Fasten the VALVE LOCK RING (9) to the wooden |
|
|
|
|
|
|
|
|
|
|
| #8 SCREWS | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
| mounting surface with #8 screws (not provided). |
|
|
|
|
|
|
|
| TUB OUTLET | ||||||
|
|
| Connect the water inlet and tub outlet lines to |
|
|
|
|
|
|
| VALVE | |||||||
|
|
| the DIVERTER BODY (6). |
|
| BODY | ||||||||||||
|
|
| TEST |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
4 | Note: Test Cap not provided. |
|
| DIVERTER | ||||||||||||||
|
|
|
| Cap the HOSE OUTLET. Remove the DIVERTER GUARD. |
|
| ||||||||||||
|
|
|
| |||||||||||||||
|
|
|
|
|
| GUARD | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove the SPOUT GUARD. Assemble the 1/4" PLUG to the SPOUT SHANK with a thread sealant. See the R800 SERIES ROUGH VALVE KIT instructions for details.
3
8
7
6
WATER INLET
4" LONG ADAPTER NIPPLES
5
SLEEVE
GUARD
SLEEVE
Turn on the water supplies.
Rotate the DIVERTER SLEEVE back and forth fully. Check all connections for leakage.
Turn off the water supplies. Replace the DIVERTER GUARD and the SPOUT GUARD. Remove the CAP from the HOSE OUTLET.
DIVERTER
SLEEVE
1/2" COPPER WATER TUBE (MIXED SUPPLY TO TUB FILLER SPOUT)
1/2" COPPER WATER TUBE INLET (MIXED SUPPLY FROM BATH FITTING)
CAP
5 HOSE |
|
|
(MIXED SUPPLY | ||
Insert the HOSE through the SLEEVE from below the mounting deck.
Thread the SLEEVE GUARD onto the HOSE END connection.
Insert the SLEEVE GUARD into the SLEEVE.
HOSE END
HOSE
6 SERVICE
TO REMOVE DIVERTER
Turn off the water supplies.
Turn HANDLE to the off position.
Remove the SLEEVE from DIVERTER by losening screw.
Using 14mm (9/16") Deep Socket, remove diverter.
SCREW
DIVERTER SLEEVE
DEEP SOCKET 14mm (9/16")
DIVERTER
M 9 6 8 3 5 5 D