PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
•Five years:
–Fiber optic products
–TW3000 Series unshielded twisted pair (UTP) transmission products
–
•Three years:
–
–EH1500 Series enclosures
–Spectra® IV products (including Spectra IV IP)
–Camclosure® Series (IS, ICS, IP) integrated camera systems
–DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry® Series hardware products, DVX Series digital video recorders, and NVR300 Series network video recorders
–Endura® Series distributed
–Genex® Series products (multiplexers, server, and keyboard)
–PMCL200/300/400 Series LCD monitors
•Two years:
–Standard varifocal, fixed focal, and motorized zoom lenses
–DF5/DF8 Series fixed dome products
–Legacy® Series integrated positioning systems
–Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
–Esprit Ti and TI2500 Series thermal imaging products
–Esprit and WW5700 Series window wiper (excluding wiper blades).
–CM6700/CM6800/CM9700 Series matrix
–Digital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days. The air filter is not covered under warranty.
–
•One year:
–Video cassette recorders (VCRs), except video heads. Video heads will be covered for a period of six months.
•Six months:
–All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
(559)
1.Model and serial number
2.Date of shipment, P.O. number, sales order number, or Pelco invoice number
3.Details of the defect or problem
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800)
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.
REVISION HISTORY
Manual # | Date | Comments |
C1420M | 1/95 | Original version. |
| 4/95 | Rev. A. Incorporates changes in Section 4.0 and Figure 1 for unit weights and dimensions and maximum camera/lens dimensions per ECO |
| 5/96 | Rev. B. Incorporates changes in heater blankets and brackets per ECO |
|
| added per ECO # |
| 5/96 | Rev. C. Figure 3 reused to remove pressure sensor switch. Refer to manual C1445M for switch wiring. Figure 5 and Section 8.2 revised to include grounding lug. |
| 7/97 | Section 7.3, step 4 revised (color: pink to blue). Added new Section 3.2 for CE and UL compliance. |
| 6/98 | Removed references to UL compliance. Changed format. |
| 11/98 | Revised Figure 4. Editing changes. |
| 7/00 | Revised manual to include grounding stud on rear plate. Revised mating connector assembly instructions and diagram. Moved exploded assembly diagram and parts |
|
| lists to new maintenance/service manual (C1420SM). Removed installation instructions for sun shroud, which has separate manual. Updated manual to new format. |
1/04 | Revised enclosure pressure from 5 psi to 8 psi. | |
12/04 | Factory preset for regulator changed to 12 psi per ECO# | |
12/04 | Revised instructions and artwork for mating connector assembly per ECO | |
1/07 | Revised Specifications section for power consumption, maximum cable distances, and enclosure mounting. | |
6/09 | Removed the mating connector assembly instructions, moved the recharging enclosure instructions, reorganized the installation section, and added a parts list and | |
|
| accessories list. Also revised the specifications for input voltage, heaters, and weight. |
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex,
DLP is a registered trademark of Texas Instruments Incorporated.
© Copyright 2009, Pelco, Inc. All rights reserved.