Pelco ES30TI manual Important Safety Instructions

Page 5

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

7.Only use attachments/accessories specified by the manufacturer.

8.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

9.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10.Installation should be done only by qualified personnel and conform to all local codes.

11.Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

12.Use only installation methods and materials capable of supporting four times the maximum specified load.

13.Use stainless steel hardware to fasten the mount to outdoor surfaces.

14.To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.

15.AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.

16.A readily accessible disconnect device shall be incorporated in the building installation wiring.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so.

Only use replacement parts recommended by Pelco.

After replacement/repair of this unit’s electrical components, conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

C1307M-C (8/07)

5

Image 5
Contents ES30TI Esprit With Thermal Imager Page Contents List of Tables List of IllustrationsImportant Safety Instructions Radio and Television Interference Regulatory NoticesPedestal Mount Wall Mount Lens Format 24 VAC 120/230 VAC DescriptionModels Parentheses are Centimeters ALL Others are Inches InstallationAC HI HOT RX+ C1307M-C 8/07 Removing the PAN/TILT Cover TXB Series Translator Board Installation OptionalFastening the Pan/Tilt Cover Reinstalling the PAN/TILT CoverOperation Configuration DisplayHOW to Operate Your System Controller Pan Tilt Type Operating NotesPatterns Programming PresetsAccessing Main Menu Preset MPT9500 KBD4000/KBD4002/KBD4000VNET300/NET350/NET4001A Endura SystemsMain Menu AGC ModeAZ/EL AZ/EL Line Azimuth Zero Contrast Direction Direction Line Display Duration Display Hot Warm Cool Cold Type Display TypeFrequency Flat Field Correction FFCTemp Change HOT Bias Limit Stops Controller PresetsClear Manual Stops PresetsLimit Stops Menu Clear Scan Limit Stops Park Time Minutes Pattern Length Power UP Mode Profile ROI Region of InterestEnabling or Disabling ROI Reset Camera Restore ALL Defaults Restore Camera Defaults Save Profile Scan Speed Sharpness Speed Profile Temp Units Zone Blank ZonesZoom Zoom Line Troubleshooting Maintenance and TroubleshootingMaintenance Symptom Unable to view activity through glass Symptom Ground loopsSymptom No video or poor video SW1-5 SW1-6 SW1-7 SW1-8 Switch SettingAppendix Table C. Switch Settings for SW2 112 232 Electrical SpecificationsProduct Warranty and Return Information ISO9001

ES30TI specifications

The Pelco ES30TI is a high-performance security camera designed for robust surveillance applications. This cutting-edge device combines innovative technology with user-friendly features to deliver exceptional video quality and reliability.

One of the main features of the ES30TI is its advanced imaging capabilities. Equipped with a high-resolution image sensor, this camera captures crisp, detailed video footage even in challenging lighting conditions. The low-light performance is enhanced by its infrared (IR) capabilities, allowing it to provide clear images in total darkness, making it ideal for nighttime surveillance. The camera also supports multiple resolutions and frame rates, offering flexibility to meet various security needs.

In terms of design, the Pelco ES30TI is built with durability in mind. Its rugged, weather-proof housing ensures that it can withstand harsh environmental conditions, making it suitable for both indoor and outdoor applications. The camera's compact and sleek design allows for discreet installation, which is particularly advantageous in urban settings where aesthetics may be a concern.

The ES30TI also integrates advanced technologies to enhance its functionality. One notable feature is the intelligent video analytics capabilities. This includes motion detection, line crossing detection, and intrusion detection. These features help in identifying potential security breaches and alerting users promptly. Additionally, the camera can be easily integrated with existing security systems, providing a seamless security experience.

Another significant characteristic of the Pelco ES30TI is its ease of use. The camera is designed with a user-friendly interface that allows for straightforward configuration and management. Users can access live feeds and recorded footage remotely through a secure network connection, providing peace of mind whether they are on-site or away.

Moreover, the ES30TI supports multiple video compression formats, allowing for efficient storage and transmission of video data. This ensures that the camera can deliver high-quality video while optimizing bandwidth and storage requirements, making it cost-effective for long-term use.

In summary, the Pelco ES30TI is a versatile and reliable surveillance solution equipped with advanced imaging technology, weather-resistant design, intelligent analytics, and user-friendly features. Its combination of performance and durability makes it an excellent choice for a wide range of security applications. Whether monitoring public spaces, commercial properties, or private residences, the ES30TI delivers the quality and reliability that security professionals demand.