Pelco C3662M installation manual DS Xpress with Internal Camera Inputs Installation, Output

Page 15

DS XPRESS (WITH INTERNAL CAMERA INPUTS) INSTALLATION

To install DS XPress with internal camera inputs, refer to Figure 7 on page 15, and then complete the following steps:

1.Plug the power cord into the power connector ì.

2.Item î=is the COM1 connector, which is used to connect RS-232-based PTZ cameras. Refer to PTZ Installation on page 29 for installation details.

3.Plug the monitor into the monitor connector ï and its power cord into an electrical outlet.

4.Connect the network port ñ to the network switch using Cat5 cable.

5.Plug the USB mouse into a USB connector ó.

6.Plug the USB keyboard into a USB connector r.

7.Plug a USB printer into a USB connector s.

8.Item t shows the connector for the 16 digital inputs and alarm output. Wire your alarm triggers into the input trigger block and connect the signal ground to a GND pin. Wire an alarm device to AO+ and AO–.

9.Plug PC speakers into the line out connector u.

10.Item is the FlashGuard cardlet relay output (bottom two pins), which can be used to trigger an alarm when a critical error occurs. Connect the alarm to the bottom two pins of the 6-pin terminal block. Refer to the FlashGuard and the WatchDog Service on page 40 for more details about the relay output. The top four pins in u are the COM5 connector, which is used to wire RS-422–based PTZ cameras.

11.Item is the audio connector bracket. From top to bottom are audio inputs 1–4, audio outputs 1–4, and four grounds.

12.Item is an optional SCSI card, which is used to connect to external storage units.

13.Connect cameras to the camera inputs . Inputs 17–32 are available only on 32-input systems.

14.The four connectors indicated by are multicamera video outputs. The following table shows how the outputs are used:

Table A. DS XPress Multicamera Outputs

DS XPress system

Output 1

Output 2

Output 3

Output 4

 

 

 

 

 

16 inputs, 1 board

1–16

Unused

Unused

Unused

 

 

 

 

 

16 inputs, 2 boards

1–8

9–16

Unused

Unused

 

 

 

 

 

16 inputs, 4 boards

1–4

5–8

9–12

13–16

 

 

 

 

 

32 inputs, 2 boards

1–16

17–32

Unused

Unused

 

 

 

 

 

32 inputs, 4 boards

1–8

9–16

17–24

25–32

 

 

 

 

 

15.Plug the power cord into an electrical outlet and turn on the power switch .

16.To turn on the system, use the power switch on the front panel of the unit.

14

C3662M (6/08)

Image 15
Contents P O R TA N T N O T E Integral Digital Sentry Page Contents C3662M 6/08 List of Illustrations List of Tables Important Safety Instructions Video Quality Caution Regulatory NoticesTypical Systems IntroductionTypical DS Enterprise Distributed System DS Enterprise Savr Installation Component InstallationRear Panel of DS Enterprise Savr DS Xpress with XMUX2 InstallationRear Panel of DS XPress with XMUX2 Output DS Xpress with Internal Camera Inputs InstallationRear Panel of DS XPress with Internal Camera Inputs Rear Panel of 9- and 16-Input DS Desktop DS Desktop InstallationRear Panel of 4-Input DS Desktop DS 1000 InstallationRear Panel of DS Rear Panel of DS RealVue XPress DS Realvue Xpress InstallationDS RealVue XPress Audio Connector DS Realvue Desktop InstallationDS RealVue Desktop Alarm Bracket Rear Panel of DS RealVue RAID DS Realvue RAID InstallationXIO Installation XIO Cable Rear Panel of DS NVR DS NVR InstallationVAU Installation DMS InstallationRear Panel of VAU Rear Panel of XMUX2-16 XMUX2 InstallationDS Enterprise SAVR/DS XPress/VAU PTZ Connections PTZ InstallationDS Enterprise Distributed System Installation C3662M 6/08 Software Installation Digital Sentry CLIENT/ADMIN SoftwareDigital Sentry SERVER/VAU Software Changing AN IP Address Changing PasswordsProcedural Instructions Changing a Computer NameChanging the Startup Mode of a Service Starting and Stopping ServicesChanging the Time Zone Configuring and Testing Odbc Connectivity System and Display Requirements for Client ComputersRules for Caching on Digital Sentry Client Computers Renaming DS Components Renaming a DS ServerRenaming a VAU Changing the SA Password Reconfiguring Dsadmin After AN IP Address ChangeConfiguring and Verifying Network Storage Connecting a Serial Input Device to a DS System Flashguardtest Flashguard and the Watchdog ServiceRAID IP Addresses Relay Output CharacteristicsSubnet mask Isolating Storage Units on a Private NetworkUsing Xpress Winview Using the Fltime UtilityUsing Realvue Diagnostic Tool Using Integral License KEY UtilityHard Drives Network Health MonitoringUsing Digital Sentry Backup Manager Backing UP the DatabaseRestoring Archived Data Rebuilding Using -FIXLOCAL Repairing and Rebuilding a Digital Sentry DatabaseTesting a Network Connection Repairing a Restored DatabaseChecking for Video Files Digital Sentry Network Speed SimulationOption #2 Running a RecoveryAfter Recovery Option #1Removing References to Local Files on Failed Hard Drives Recovering Video Files Without a Database BackupVideo Specifications DS RealVue DesktopSpecifications DS RealVue RAID Specifications DS RealVue XPress IP CIF Specifications DSXMUX-2 Specifications DS XPressSpecifications DS Desktop Specifications DS Enterprise Specifications DS NVR Product Warranty and Return Information ISO9001
Related manuals
Manual 4 pages 12.31 Kb

C3662M specifications

The Pelco C3662M is a state-of-the-art camera designed for robust surveillance and exceptional performance in various environments. Built for security applications, this camera features advanced imaging technology that ensures reliable monitoring and high-quality video capture.

One of the main features of the C3662M is its high-resolution image sensor. This sensor captures clear and crisp images, even in low-light conditions. With a resolution of 2 megapixels, the camera delivers detailed footage that can be crucial for identification purposes. The camera is capable of generating high-definition video streams, providing security operators with the clarity they need to assess any situation effectively.

The C3662M also incorporates advanced technology such as Wide Dynamic Range (WDR), which allows it to perform exceptionally well in scenes with contrasting lighting. This feature ensures that both the bright and dark areas of a scene are captured with excellent detail, making the camera particularly useful in environments like parking lots or entryways where lighting conditions can vary greatly.

Another critical characteristic of the C3662M is its low-light performance. Equipped with infrared (IR) capabilities, the camera can operate effectively in complete darkness, making it an ideal choice for 24/7 surveillance. The IR illumination allows the camera to capture clear images even when there is no visible light.

The C3662M is also designed for versatility in its deployment. It supports various mounting options and configurations, enabling users to install the camera in various locations, from indoor environments to outdoor settings. The rugged construction of the camera ensures it can withstand adverse weather conditions, making it suitable for use in challenging environments.

In terms of connectivity, the C3662M is compatible with various video management system solutions. It can easily integrate into existing security infrastructures, allowing for seamless operation and monitoring.

With its combination of high-resolution imaging, advanced WDR technology, and versatile installation options, the Pelco C3662M stands out as a premium choice for security applications. This camera addresses the needs of modern surveillance with reliability, ensuring that users can maintain peace of mind through effective monitoring capabilities.