Pelco C10DN manual Connecting DAY/NIGHT Filter Control, Signal Voltage

Page 14

CONNECTING DAY/NIGHT FILTER CONTROL

In some installations, high infrared (IR) illumination or other light sources may interfere with the camera’s automatic day/night mode operation. Use an external day/night filter switch, such as a photosensor, to keep the camera from constantly switching filters.

The control signal input responds as shown in Table C.

Table C. Day/Night Control Signal

Signal

Voltage

Day/Night Mode

 

 

 

Open or High

3.0 V to 3.3 V

AUTO

 

 

 

Short or Low

-0.3 V to 0.3 V

B-W

 

 

 

NOTES:

•Do not exceed the values listed in Table C.

•The C10DN Series camera responds only to the input signal from the switch. It does not provide enough power to drive an external device.

To connect an external day/night filter switch to the camera, refer to Figure 6, and then complete the following steps:

1.Turn off power to the camera.

2.If necessary, use a small Phillips screwdriver to remove the connector cover from the rear panel (refer to Figure 6).

3.If necessary, plug the external control connector assembly (supplied) into the camera. Then use a small Phillips screwdriver to secure the assembly cover to the rear panel.

4.Use 100-ohm twisted pair cable to wire the device to the enclosed connector assembly. The decision to use shielded cable depends on your installation; shielded cable may be optional.

D&N CONTROL

PIN 7

 

 

 

 

 

PIN 1

 

 

 

SIGNAL INPUT

 

 

 

 

 

 

 

 

GND (6)

 

 

 

 

 

 

 

 

Figure 6. Day/Night Filter Control Configuration

5.Wire the camera to the external switch as follows:

•Pin 7 (brown, signal input) to the (+) positive lead on the external switch.

•Pin 6 (black, ground) to the (–) negative lead on the external switch.

•Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).

6.Change DAY & NIGHT to EXT. (external) on the EXPOSURE SETTINGS menu.

7.Configure the external switch as follows:

•Open or High: Camera operates in AUTO mode.

•Short or Low: Camera operates in B-W mode.

14

C2944M-G (6/09)

Page 13 Page 15
Image 14
Page 13 Page 15
Contents C10DN Series Camera Contents List of Illustrations List of TablesGraphic Symbol Explanation Important Safety Instructions Equipment Handling Precautions Regulatory NoticesModels Optional AccessoriesDescription Required ToolsCamera Layout Lens Mounting InstallationWiring AN Auto Iris Lens Mounting the LensTable A. Video Coaxial Cable Requirements Connecting VideoCamera Mounting Cable Type Maximum DistanceConnecting Power C10DN-7X Camera onlyConnecting AC Power Connecting AC PowerConnecting DC Power Connecting DC PowerDo not exceed the values listed in Table C Connecting DAY/NIGHT Filter ControlSignal Voltage Move the button up or down Accessing the Setup MenusNavigating the Menu Move the button left or rightSetup Menus Function SETMain Menu Pixel CorrectionProfiles Exposure SettingsFunction Settings ActiveEclipser Exposure SettingsAuto Exposure Automatic Gain Control DC Iris LevelFlickerless DAY and NightFilter Limit Function SettingsDetect Time Line SyncGamma White BalanceChroma SharpnessTitle Select this option to configure the camera titleMasking System Information Save AS CustomPixel Correction Lens Focusing Fixed focal length lens onlyVarifocal lens only Camera Synchronization Manual White Balance Calibration Specifications Operating Humidity Operating TemperatureStorage Temperature Storage HumidityProduct Warranty and Return Information

C10DN specifications

The Pelco C10DN is an advanced surveillance camera designed for both indoor and outdoor applications. It is distinguished by its compact design, ease of installation, and high-performance capabilities. The C10DN is part of Pelco's renowned range of security cameras, tailored to provide essential features that cater to a wide array of monitoring needs.

One of the standout features of the Pelco C10DN is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crystal-clear images with exceptional detail. It operates effectively in varying lighting conditions, boasting a wide dynamic range that ensures visibility in bright highlights and deep shadows alike. The camera also supports high-quality digital video output, which enhances image processing and improves overall video clarity.

The C10DN utilizes advanced technologies to enhance its performance. Among these is the integration of Day/Night functionality, allowing the camera to automatically switch between color and monochrome modes based on ambient light levels. This capability enables continuous surveillance and helps maintain image quality during low-light conditions, making it ideal for nighttime monitoring. Furthermore, it features built-in infrared illumination options that extend its effectiveness even in complete darkness.

In terms of durability and resilience, the Pelco C10DN is constructed with robust materials suitable for demanding environments. It complies with IP66 ratings for ingress protection, ensuring that the camera is resistant to dust and water, which is vital for outdoor installations. Additionally, its rugged design includes options for mounting on various surfaces, keeping installation versatile and convenient.

The camera is equipped with multiple lens options allowing users to choose the appropriate focal length to meet their specific surveillance needs. Additionally, it supports various control protocols, including Pelco-D, enabling seamless integration with existing surveillance systems.

In summary, the Pelco C10DN is engineered to meet the modern demands of security and surveillance. Its high-resolution imaging, advanced Day/Night technology, durable construction, and flexible installation options combine to make it an excellent choice for users seeking reliable and effective monitoring solutions across a range of settings.
Top Page Image Contents