PYLE Audio PYD-1950, PYD-1910 Presetting the Controls Before Use, Connecting the Mixer Inputs

Presetting the Controls Before Use

Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust the mixer’s controls BEFORE connecting AC power or turning on the unit.

Set up the mixer controls like this before you start:

CONTROL	SETTING
Power On/Off	OFF

Connecting High Level Output Audio Sources

Connect up to 8 such sources (tuner, cassette deck, CD Player, camcorder or VCR) to the input jacks for Line 1 (if not being used as Phono 1 input), Line 2, Line 3 (if not being used as Phono 2 input), Line 4, Line 5 and Line 6. Please note that Phono 1 and Line 1 (as well as Phono 2 and Line 3) use the same jacks. The selector switch(e)s below the jacks should be set to Line position if the jacks are used for the High Level input sources described here.

Balance	MID
Gain	MID
Tone Controls, Treble, Mid & Bass	0
MIC 1/2, CH 1/2/3/4, Master & Cue Levels	0
Crossfader	CENTER

Connecting the Mixer Inputs

This mixer permits connection of up to eight (8) audio input sources,and two microphones. Such a system might include, for example:

Two Microphones	Two Microphones	Two Microphones	Two Microphones
Two Turntables	Eight CD players	Two Turntables	Two Turntables
Six CD players		Three CD players	Four CD players
		Three Cassette Decks	One Rhythm Synth
			One Cassette Deck
Please observe	Do not connect any audio source with a HIGH LEVEL OUTPUT to the
	LOW LEVEL PHONO 1 or PHONO 2 mixer audio input jacks (an audio
the following:	source output with a volume control is HIGH LEVEL).

Use RCA type patch cables

High Level Output

Audio Source

LEFT output

RIGHT output

CD player, cassette deck, camcorder, VCR, etc.

NOTE!

If you use a High Level Output Audio Source(s) in the Phono1/Line1 (and/or Phono2/Line3) input jack(s), be sure to place the Input Select switch in the LINE1 (and/or LINE3) position(s)!

Connecting Microphones

Microphone 1. Connect a balanced/unbalanced low impedance (600 Ohm) XLR type mic OR a low impedance mic with a 1/4” plug to the MIC 1 jack in the upper left corner of the mixer control panel.

Use 1/4” or

XLR-type jack

MIC 1

Microphone 2. Connect a high quality balanced/unbalanced low impedance (600 Ohm) microphone with a 1/4” plug to the MIC 2 jack on the lower left corner of the mixer’s back panel.

MIC 2

Use 1/4” jack

Connecting Turntables and Other Level Output Audio Sources

Connect up to 2 turntables to the Phono 1 and Phono 2 input jacks. Please note that Phone 1 and Line 1 (as well as Phono 2 and Line 3) use the same jacks. The selector switch below the jacks should be set to Phono position if the jacks are used for phono inputs.

When using a turntable, you should also securely connect its ground wire (usually green or black) to the Ground screw on the input panel of the mixer.

Use RCA type patch cables

Magnetic cartridge turntable

LEFT output

RIGHT output

GROUND wire from turntable

NOTE!

If you use a Turntable in the Phono1/Line1 (and/or Phono2/Line3) input jack(s), be sure to place the Input Select switch in the PHONO1 (and/or PHONO2) position(s)!

6 – Pyle Pro Mixer Owner’s Manual Pyle Pro Mixer Owner’s Manual – 7