PYLE Audio PYD-1930, PYD-1950, PYD-1910, PYD1920 Using the Mono/Stereo Mode Switch, Troubleshooting

Page 8

Using the Mono/Stereo Mode Switch

When the MASTER MONO/STEREO switch is in the MONO position, the mixer combines the right and left channels and sends them to the OUTPUT R and L jacks. These combined outputs can be used by a monoaural amplifier, such as a PA amp.

In the STEREO position, right and left channels remain separate. The mixer outputs can be used by a stereo amplifier or recorder.

The ZONE MONO/STEREO switch works similarly, except that its setting affects the ZONE R & L Outs.

Using the Crossfader with the Assign Switches

For crossfading effects, you can assign any of the four channels to either A or B sides of the crossfade mix using the Crossfade assign knobs.

When the crossfade slider is in the center position, the two assigned channels play equally. Sliding the control towards the A position will increase the level of A and fade out B proportionally to the distance from center. Likewise, sliding the control towards the B position will increase the level of B and fade out A.

Using the Echo Controls (PYD-1920 and PYD-1940)

The built-in Echo effect is applied to the total mix. To turn on the Echo mode and activate the DELAY/REPEAT cycle, press the ECHO ON/OFF switch.

To change the length of time a sound is repeated, increase of decrease the REPEAT control. To vary the time in between the repeats, increase or decrease the DELAY control.

To adjust the output level of the echo, increase or decrease the LEVEL control.

Using the Sound Effects (PYD-1930 and PYD-1940)

There are eight pre-programmed sound effects for your selection. Press and hold any button to generate a sound which is added to the mix. The sound will play continuously until you release the button.

4.To playback the recorded sample ONCE, turn the SAMPLER MODE switch to SINGLE, and press START/STOP. The LED will go on, indicating that a sample is playing. Pressing START/STOP during playback will stop the playback.

Each time you press the START/STOP control, the unit will replay the recorded sample from the beginning and play it through the end of the recorded sound. Rapid, consecutive pressing of the START/STOP button will create an interesting stuttering effect.

5. To playback the record sample repeatedly (”looping”), set the SAMPLER MODE switch to REPEAT, and press START/STOP. The mixer will play the sampled recording all the way through, and thenrepeat it until you press the START/STOP button.

6. To adjust the speed of the playback signal, rotate the SAMPLE PITCH control to reduce or increase the pitch of the sample during playback.

7. To adjust the level of the sample playback as it enters the mix, rotate the SAMPLE LEVEL to increase or decrease the level.

Troubleshooting

Your mixer should require very little maintenance. If you have problems, refer to the chart below for possible solutions. If you cannot solve the problem, contact a qualified technician for assistance.

 

PROBLEM

POSSIBLE SOLUTION

 

 

Nothing works

• Check the AC connection. Make sure the AC outlet is “live.”

 

 

 

• Check the power connection to the rest of the system (receiver/amplifier, etc.)

 

 

 

 

 

 

No signal from an

• Check the control setting

 

 

audio input

• Check the connection between the mixer and the input source

 

 

source

 

 

 

 

 

 

 

Hum from PHONO

• Check that the turntable’s ground wire (usually black or green) is fastened securely to the GROUND

 

 

SCREW on the mixer input panel

 

 

 

 

 

 

 

 

 

Hum from other

• Make sure there are no low level inputs connected to the LINE input jacks

 

 

source

 

 

 

 

 

 

 

Feedback is

• Move the microphone further away from the output speakers, or use a directional microphone

 

 

present

 

 

 

 

 

 

 

 

 

 

The SPEED control lets you raise or lower the pitch of the sound effect, and the VOLUME control allows you to increase or decrease the effect’s volume level within the mix.

Using the Digital Sampler (PYD-1950)

The PYD-1950 mixer contains a digital sampler circuit which can record 5 different samples to the internal recording IC. These samples can then be assigned to CH 1, CH 2, CH 3, CH 4 and the MIC channel for playback. At the time of playback, the SPEED control can be adjusted to change the pitch of the sample.

Follow these steps to record a sample:

1.Play the audio source for recording as a sample.

2.While it is playing, press the desired cue/sample channel assign button (i.e., CH 1, CH 2, CH 3, CH 4 or MIC).

3.To record the source to that channel, set the SAMPLER MODE switch to the RECORD position and press the START/STOP button to begin recording. The LED will go on, indicating recording is in progress. To stop recording, press the START/STOP button again. Please note that the recording IC is limited to 12-second samples, so in the event you do not press stop, it will automatically stop after 12 seconds

Care and

Maintenance

Your Pyle Pro Mixer is an example of superior design and craftsmanship. The following suggestions will help you care for your mixer so you can enjoy years of use:

Keep the mixer dry. If it gets wet, wipe immediately.

Use the mixer only in well- ventilated installations.

Handle the mixer gently and carefully - do not drop!

Keep the mixer away from dust and dirt.

Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents or detergents!

Please complete warranty card, detach and return

Place

Stamp

Here

PYLE PRO Audio, Inc.

1600 63rd Street

Brooklyn, NY 11204

12 – Pyle Pro Mixer Owner’s Manual

Pyle Pro Mixer Owner’s Manual –13

Image 8
Contents Specifications PYD1910/1920/1930/1940/1950Features and Controls PYD1910 Mixer Input/Output Features all modelsYour Pyle PRO Series Performance Mixer Stereo Line Inputs let you connectEcho On/Off Switch Zone Balance Control Zone Mono/Stereo SelectorMIC1/2 Tone Controls Presetting the Controls Before Use Connecting the Mixer InputsConnecting High Level Output Audio Sources Connecting MicrophonesUsing the Channel Input Gain Controls Connecting the Mixer OutputsUsing Headphones Connecting the LampUsing the Mixer Controls Using the MicrophoneUsing the Mono/Stereo Mode Switch Using the Crossfader with the Assign SwitchesUsing the Echo Controls PYD-1920 and PYD-1940 Using the Sound Effects PYD-1930 and PYD-1940

PYD-1940, PYD-1950, PYD-1930, PYD-1910, PYD1920 specifications

PYLE Audio has established itself as a prominent name in the audio equipment industry, delivering high-quality products tailored for professional and home use alike. Among its impressive lineup, the PYD series—comprising the PYD1920, PYD-1910, PYD-1930, PYD-1950, and PYD-1940—stands out for its remarkable features, cutting-edge technology, and outstanding performance.

The PYD1920 is designed with versatility in mind. It boasts a peak power output of 2000 watts, making it an excellent choice for both live sound and home audio systems. Featuring advanced digital signal processing, this model ensures crystal-clear sound quality while minimizing noise and distortion. The PYD1920 is equipped with multiple input options, including HDMI, USB, and RCA connectors, ensuring compatibility with various devices.

Following closely is the PYD-1910, which focuses on delivering an impressive audio experience in a compact design. With a peak output of 1000 watts, it remains powerful without sacrificing portability. The PYD-1910 is fitted with a built-in Bluetooth receiver for seamless connectivity to mobile devices and laptops, allowing users to stream music with ease. Its intelligent protection circuitry prevents overheating and damage from voltage spikes.

The PYD-1930 enhances the listening experience with its multi-channel configuration. This model supports a variety of audio formats and includes integrated EQ settings for tailored sound. With an output of 1500 watts, it packs a punch that's ideal for parties or larger gatherings. The intuitive interface allows users to control their audio settings effortlessly, making it suitable for both beginners and experienced audio enthusiasts.

Exploring further, the PYD-1950 is engineered for high-fidelity sound reproduction. It features a unique low-frequency enhancement technology that boosts bass response, perfect for those who enjoy deep, immersive sound. Additionally, its sleek design and LED display add a modern touch, while the robust cooling system ensures its reliability during extended use.

Lastly, the PYD-1940 prides itself on user-friendly features, including remote control operation and customizable sound profiles. With a solid output of 1200 watts, it offers a robust solution for various audio applications. Its striking design, combined with uncompromising performance, makes the PYD-1940 a popular option among users seeking both functionality and style.

In summary, the PYLE Audio PYD series offers a range of powerful audio solutions, with each model equipped with unique technologies and features aimed at delivering exceptional sound quality. Whether for professional use or personal enjoyment, these models cater to diverse audio needs.