Stovax 8701CFCHEC Method 2 no Frame, To replace the doors and panels, refer to Replacing Parts

Page 19

INSTALLATION INSTRUCTIONS

INSTALLATION

•Feed the wires for the remote touch pad through the grommet in the left side of the loose box

The wires are then fed inside the firebox and routed through the available access

•Replace the loose box inside the main firebox ensuring the wires are not trapped

•Replace the three wing nuts and seven screws

•Connect the gas supply and check for leaks

•Replace the rear panel ensuring the bottom edge locates in the tapered brackets, Diagram 29

29

AR1968

NOTE: To check gas pressure refer to paragraph 4.11

•Replace the splitter plate

•Locate the rear two tabs into the rear panel

•Engage the two side slots over the screws and secure,

Diagram 30

30

To replace the burner:

•Locate the left-hand side into the burner bracket

•Lower the right-hand side to engage the injector onto the venturi and also the pilot into the aperture in the burner skin

•Push the burner to the right and engage the burner into the slot in the bracket

•Replace the fixing screw, Diagram 31

31

AR1965

To replace the doors and panels, refer to Replacing Parts, Section 3 and 5

4.9METHOD 2 - NO FRAME

The front of the chimney breast has to be studded and boarded to allow the edge kit to be fitted.

For this cool-wall Edge installation, the convected heat of the fire is channelled into the cavity between the existing chimney and the false wall, then vented at the top. The vent should have a minimum open area of 200mm.

•Proceed as described in Section 4.1 to 4.8, but do not fit the frame brackets

You have now removed the box from the appliance and should use the following:

•Fit the edge kit to the two sides and lower edge using the screws and rawl plugs provided, Diagram 32

32

AR1912

•Stud the face of the chimney breast using the method described in Section 3.3, Diagrams 14, 15.

Do not fix any horizontal stud work above the appliance as this will prevent the convected air escaping through the vents

•Fit the non-combustible board and the plasterboard as described in Section 3.3

•Apply plaster skim to the front of the chimney breast

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Studio PR0957 Studio Issue 3 JanuaryCovering the Following Model Studio 1 conventional flue GAS CHECK APPLIANCE COMMISSIONING CHECKLISTFLUE CHECK FailLighting the Studio MAN ModeUser Instructions General2B Touch PAD Control Emergency Shut OFF Cleaning the StudioUsing the allen key provided Changing the Studio BatteriesHOT SURFACES Arrangement of Fuel BEDFire will not Light Technical Specification Installation InstructionsCovering the Following Models Qty Description Fixing Kit containing Packing ChecklistStudio 846 1046 520 750 950 424 12.5 Steel Frame DimensionsDimension Studio Bauhaus Frame DimensionsVentilation SITE REQUIREMENTSFlue Options GAS Supply440 1160 Safety Precautions InstallationInstallation of the appliance Stud Work Installation Method 1 Frame Stud Work InstallationThere is AN Optional Duct KIT, Code No AR1903 Stud Work Installation Method 2 Edge Door is now free to remove, Diagram Masonry chimney InstallationRemove the remaining rear and lower panel, Diagram Method 1 Frame Method 2 no Frame To replace the doors and panels, refer to Replacing Parts,Assembling the Appliance Both Method 1 or 2 Masonry InstallationTouch PAD Control Thermostatic Remote ControlBy thermostatic remote control Using the fire’s touch pad Lighting the StudioCommissioning For future reference, record the installation details onCommissioning Servicing Instructions Servicing / Fault Finding ChartsServicing Requirements Flame Failure Functional Check Ignition Functional CheckDecorative Frame Replacing PartsWindow Frame Assembly GeneralEnsure no stone pebbles fall into the pilot area Glass WindowBlack Enamelled Panels MaIN BurnerIgnition Lead MaIN Control AssemblyPilot Unit Assembly Remove the screw retaining the pilot cover, DiagramControl BOX Magnetic safety valveRemove the cover fixing screw, Diagram GAS ValveChanging between Gas Types Debris Area AccessMain injector Primary Aeration PlateAccess to the pressure test point can now be reached Diagram Pressure and Leak Testing the ApplianceG30 N/A ShoRt Spares ListG31 N/A Service Records Member of the Stovax Group

8701CFCHEC, P8700CFCHEC, P8701CFCHEC, 8700CFCHEC specifications

Stovax, a renowned name in the world of wood-burning stoves and fireplaces, offers a range of high-performance heating solutions designed for both efficiency and aesthetics. Among their standout models are the P8701CFCHEC and P8700CFCHEC, as well as their closely related variants, 8701CFCHEC and 8700CFCHEC. These models showcase the commitment of Stovax to blend modern technology with traditional heating methods.

One of the most notable features of the P8701CFCHEC and P8700CFCHEC models is their advanced combustion technology. Designed to maximize efficiency, these stoves provide a clean and efficient burn, minimizing emissions and maximizing heat output. This ensures not only a warm environment but also compliance with contemporary environmental standards. The combustion system is engineered to enhance air circulation within the firebox, which promotes a more complete burn of the fuel, resulting in reduced fuel consumption.

Both models come with a contemporary yet adaptable aesthetic, allowing them to seamlessly fit into a variety of interior design styles. Their sleek faces and clean lines add a touch of modern sophistication, making them suitable for both traditional and contemporary homes. The large glass windows patented by Stovax provide an expansive view of the flickering flames, creating a cozy atmosphere while also serving as a focal point in any room.

In terms of versatility, the P8701CFCHEC and P8700CFCHEC models allow for multiple installation options. They can be fitted into existing fireplaces or used as stand-alone units, catering to different homeowner preferences. Additionally, they can be used with various flue systems, enhancing their adaptability to different living spaces.

Further elevating the user experience, these stoves are designed with easy-to-use controls that allow for precise adjustment of the heat output, making it easy to maintain a comfortable living environment. The built-in air wash system helps keep the glass clean, ensuring that users can enjoy uninterrupted views of the fire without the hassle of frequent maintenance.

In conclusion, the Stovax P8701CFCHEC and P8700CFCHEC models, along with their variants, represent a fusion of classic wood-burning technology with contemporary design and unparalleled efficiency. They are perfect choices for anyone looking to enhance their home heating solution while also adding a touch of style and comfort.
Top Page Image Contents