Stovax Huntingdon 30 manual Control Upgrade, Safety Precautions, Installation of the Stove

Page 10

INSTALLATION INSTRUCTIONS

INSTALLATION

IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS AT THE FRONT OF THIS BOOKLET.

FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SERVICING SECTION, REPLACING PARTS

1.CONTROL UPGRADE

1.1This stove is fitted with a control valve that can be easily upgraded to battery powered remote control. There are two versions of this control which can be obtained through your local Gazco stockist.

1.2This upgrade can be fitted before or after installation but if side clearances are limited then it will be easier to upgrade the stove before installation. Full instructions are included with the kit.

1.3STANDARD REMOTE CONTROL This remote control can control the gas appliance after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NUMBER 8455.

1.4THERMOSTATIC AND TIMER REMOTE CONTROL This remote control can control the gas appliance after the pilot has been lit. In ‘MANUAL MODE’ it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner off leaving the pilot burning. In ‘AUTO MODE’ it will automatically regulate the room temperature. In ‘TIMER MODE’ it will turn the fire on and off according to a pre-set programme and automatically regulate the room temperature during two on periods. GAZCO PART NUMBER 8456

2.SAFETY PRECAUTIONS

2.1This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance.

2.2All the instructions must be left intact with the user.

2.3In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.

2.4This appliance is intended for use on a governed gas installation and set to the required pressure.

2.5Keep all plastic bags away from young children.

2.6Do not place any object on or near to the stove. Allow adequate clearance above the stove. See diagram 2 page 9.

2.7The stove is fitted with the Gazco Flue Sure System, which cuts off the gas supply to the stove in the event of incorrect flue operation. If the system shuts off the gas supply, this indicates there is insufficient flue pull. If this happens, a

minimum of 10 minutes must be allowed before trying to relight. If this safety device is continually shuts off the gas it can suggest a serious problem:

• Contact Gazco

2.8Do not alter or tamper with the Flue Sure System. Use only genuine Gazco replacement parts when servicing the system - refer to the Servicing Section, Replacing Parts.

3.INSTALLATION OF THE STOVE

3.1Flue Pipe Installation

•Open the carton

•Remove the accessory carton and stove unit

•Decide whether to use top or rear flue exit

The stove is factory built for rear flue exit but it can be changed to top exit by swapping the flue spigot and blanking plate located on the stove.

3.2• Position the stove ensuring all appropriate clearances are observed

3.3Having run the gas supply to the stove:

• PURGE THE SUPPLY PIPE

This is essential to expel any debris that can block the gas controls.

•Connect the gas supply to the 8mm-compression elbow at the right-hand rear corner of the stove

There is a cutout in the right-hand rear leg to enable a straight connection to the rear of the stove, Diagram 3. A gas soundness check must be completed up to the gas inlet connection.

3

AR0934

3.4• Check the pull of the flue system by applying a lighted smoke pellet to the flue system opening

If there is a definite flow into the chimney, proceed with the installation. If not, warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY REQUIRE ATTENTION - SEEK EXPERT ADVICE

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Huntingdon 30 Coal Effect Stove Contents Flue Check Pass Fail Appliance Commissioning ChecklistGAS Check Lighting the Stove User InstructionsGeneral Minutes . Turning the Stove OFFCleaning the Fire Stove Stays HOT for a Long Time After ShutdownAdvice on Handling and Disposal of Fire Ceramics Fuel BED ArrangementGazco Flue Sure System Installation DetailsReplacing the Door Flame Failure DeviceNOX Installation InstructionsTechnical Specification CATFlue and Chimney Requirements Installation of the GAS SupplySite Requirements Appliance LocationSafety Precautions InstallationControl Upgrade Installation of the StoveFuelbed Arrangement Replacing the Door Lighting Commissioning CommissioningServicing / Fault Finding Charts Servicing InstructionsIgnition Functional Check Flame Failure Functional CheckPilot Unit Replacing PartsMain Burner Make Sure the Appliance is Cold Before Starting Work on ITPiezo Ignition Lead and PiezoGAS Valve Magnetic Safety Valve Main InjectorPrimary Aeration Plate Control Upgarde Changing Between GAS TypesShort Spares List Service Records Member of the Stovax Group

Huntingdon 30 specifications

The Stovax Huntingdon 30 is a highly regarded wood-burning and multi-fuel stove that embodies both traditional aesthetics and modern efficiency. Designed for both contemporary and classic interiors, its versatile appeal makes it a popular choice among homeowners seeking warmth and character in their living spaces.

One of the standout features of the Huntingdon 30 is its robust construction, crafted from high-quality steel with a cast iron door. This design not only enhances durability but also contributes to the stove's ability to retain and radiate heat effectively. The large viewing window offers a picturesque view of the flames, creating a cozy ambiance while highlighting the efficiency of the combustion process.

The Huntingdon 30 is equipped with advanced combustion technology, ensuring a cleaner burn with reduced emissions. This stove utilizes Stovax’s Cleanburn technology, which maximizes combustion efficiency by recycling gases that would otherwise escape up the flue. This innovative approach allows the stove to achieve high efficiency ratings while minimizing environmental impact.

With a nominal heat output of 8 kW, the Huntingdon 30 is suitable for medium to large rooms, making it an ideal choice for various living spaces. Its Airwash system keeps the glass panel clean, providing uninterrupted views of the fire and reducing the need for frequent cleaning. The stove also features adjustable primary and secondary air controls, allowing users to set the combustion process according to their heating needs.

Another notable characteristic is the stove's versatility in fuel options. Designed for both wood and solid fuel burning, the Huntingdon 30 can accommodate a range of fuel types, offering flexibility to suit user preferences and availability. Additionally, its integral log store provides a convenient space for wood storage, ensuring that logs are easily accessible for fueling the fire.

Furthermore, the Huntingdon 30 is available in various finishes, including classic black, ivory, and a range of enamel options, allowing homeowners to select a model that complements their décor. The stove is also compatible with various flue configurations, making installation straightforward in different settings.

In summary, the Stovax Huntingdon 30 is more than just a heating appliance; it is a centerpiece that combines style, efficiency, and practicality. With its advanced features and elegant design, it continues to be a beloved choice for those looking to enhance their home's warmth and charm while remaining eco-conscious.
Top Page Image Contents