Samsung DVD-HD850/XEL manual Controlling a TV with the Remote control, Firmware upgrade, Reference

Chapter 6

R E F E R E N C E

Controlling a TV with the Remote control

The remote control can also be set up to control most TVs. To program the remote control, use the code that corresponds to your brand.

TV Codes

BRAND	CODE	BRAND	CODE
ANAM	10, 11, 12, 13, 14, 15, 16, 17, 18	NORDMENDE	72, 73
AIWA	82	NOKIA	74
BANG&OLUFSEN	57	PANASONIC	53, 54, 74, 75
BLAUPUNKT	71	PHILIPS	06, 55, 56, 57
BRANDT	73	PHONOLA	06, 56, 57
BRIONVEGA	57	PIONEER	58, 59, 73, 74, 75
CGE	52	RADIOLA	06, 56
CONTINENTAL EDISON	75	RADIOMARELLI	57
DAEWOO	19, 20, 23, 24, 25, 26, 27, 28, 29,	RCA	45, 46
	30 , 31, 32, 33, 34	REX	74
EMERSON	64	SABA	57, 72, 73, 74, 75
FERGUSON	73	SALORA	74
FINLUX	06, 49, 57	SAMSUNG	01, 02, 03, 04, 05, 06, 07, 08, 09
FORMENTI	57	SANYO	41, 42, 43, 44, 48
FUJITSU	84	SCHNEIDER	06
GRADIENTE	70	SELECO	74
GRUNDIG	49, 52, 71	SHARP	36, 37, 38, 39, 48
HITACHI	60, 72, 73, 75	SIEMENS	71
IMPERIAL	52	SINGER	57
JVC	61, 79	SINUDYNE	57
LG	06, 19, 20, 21, 22, 78	SONY	35, 48
LOEWE	06, 69	TELEAVA	73
LOEWE OPTA	06, 57	TELEFUNKEN	67, 73, 75, 76
MAGNAVOX	40	THOMSON	72, 73, 75
METZ	57	THOMSON ASIA	80, 81
MITSUBISHI	06, 48, 62, 65	TOSHIBA	47, 48, 49, 50, 51, 52
MIVAR	52, 77	WEGA	57
NEC	83	YOKO	06
NEWSAN	68	ZENITH	63

R E F E R E N C E

Firmware upgrade

Introduction

Samsung will often support the software upgrade to improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung.com).

Because the specially new mpeg4 codec continues and it is appearing. What improvements are made depends on the upgrade software you are using as well as the software that your DVD-player contained before the upgrade.

How to make an upgrade disc

Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings:

1

You have to download a new file through Download Center of Samsung Internet Site (www.samsung.com).

2Note

Write the file to Disc using CD-RW	- File System CD-ROM ISO Level
	- Character set ISO 9660
of your computer.
	- Finalized, single session
	- Write speed low
Upgrade procedure

1

Open the disc tray.

Place the disc on the tray. Close the tray.

The Firmware upgrade screen appears

Firware upgrade

appears on the display

NOBLEX 66

1.Turn on the TV.

2.Point the DVD’s remote control at the TV.

3.While holding the TV POWER button down, enter the code for your brand.

4.If the TV turns off, setup is complete. Enter other codes of the same brand if the first code does not work.

2

Press the ➛/❿ buttons to select Total, then press the ENTER button

▼

Firware upgrade starts

-In the middle of the writing, the tray will open automatically. After taking out the disc, please wait for about 2 minutes.

-If the unit was succesfully updated, the unit will turn off and on after closing the tray automatically. When the unit turns on, this screen will display.

You can control the TV POWER, CH ( , ), VOL (+, -) and TV/VIDEO functions of another manufacturer's TV.

-The remote control may not be able to control every model TV of the brands listed.

-If you replace the remote control's batteries, set the brand code again.

e.g) For Samsung 2 TVs

While holding down the TV POWER button, enter 0 and then 1.

3

Press the number buttons to select the desired language

Note

-If the “Select Menu Language” doesn’t appear, please contact to “Samsung Service Center”.

-Do not press any button and unplug the power code during upgrade.

-The upgrade procedure may change, refer to the web site (www.samsung.com).

Reference

ENG-58 ENG-59