Samsung SNC-B5368P manual English

Page 3

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock

11.Do not expose the product to the direct airfl ow from an air conditioner. Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera.

12.If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not fl ow inside the housing. Otherwise, external high, humid air may fl ow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature.

OVERVIEW

CAUTION

1.Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.

2.Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock.

3.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

4.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage to the product.

5.Keep out of direct sunlight and heat radiation sources. It may cause fi re.

6.Install it in a place with good ventilation.

7.Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor.

8.Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

10.When using the camera outdoors, moisture may occur inside the camera due to temperature difference between indoors and outdoors. For this reason, it is recommended to install the camera indoors. For outdoor use, use the camera with built- in fan and heater.

English _3

Image 3
Contents Network Camera Overview English FCC Statement Important Safety Instructions Contents Using the Live Screen Connecting to the CameraLogin Installing ActiveXCompatible IP Routers Product FeaturesRecommended PC Specifications Compatible PoE SwitchesIP Installer CD WHAT’S IncludedScrew Dust-proof Plate Description Signal of the camera outputsAT a Glance AppearanceGND Used for earth-grounding Reset ButtonInside Consists of two different portsLens ComponentsRelease Lock Testing the cameraWiring Cover CompartmentRemoving the Covers Installation & connectionPower Monitor Network Connecting with Other DevicePower Supply Connecting to the monitorConnecting to the I/O port box Alarm I/O Wiring DiagramAlarm GND Alarm OUT Installation Precautions before installationInstalling the camera Installation & connection Adjusting the monitoring direction for the camera You can configure the camera settings using the Web Viewer HOW to USE the Keyboard ControllerFactory Defaults Main MenuProfile Backlight Select either BLC or WDR Camera SetupCamera ID IrisSENS-UP MotionDNR ShutterSelect Camera SET DAY/NIGHT You can specify a recording mode according to the sceneDAY/NIGHT White BALReverse Digital ZoomDetail AGC Color SUPYou will see dots on the screen Zone SetupPrivacy Zone Select the Pixel LevelYou can set the font color of the user interface Factory DefaultOthers OSD ColorYou can check the system information  The camera type may different, depend on the video signalSystem Info LanguageNetwork connection and setup Select Status from the Settings menu of the IP Router Network connection and setupSetting the IP Router Connecting to the camera from a local PC in the LAN Connecting the Camera Directly to Local Area NetworkingIP Address Setup Buttons used in IP InstallerURL Static IP Setup Manual Network SetupAuto Set English Auto Network Setup Dynamic IP Environment Setup Dynamic IP SetupPort Range Forward Port Mapping Setup Connecting to the Camera from a Shared Local PCManual Port Range Forwarding Ex http//mfffe42.websamsung.net Connecting to the Camera from a Remote PC VIA the InternetNormally, you would Connecting to the CameraUsing URL Connecting via URL If the Http port is other thanTo check the Ddns address LoginFor Windows XP Service Pack 2 users Installing ActivexUsing the Live Screen Backup To capture the snapshotTo print out the screenshot To record a video Click on the scene to recordRecorded space, recording will be forcibly ended Click OK Accessing the Setup Screen Setup screenQuality Adjust the picture quality from 1 to Default SetupTo configure the video settings Contrast Adjust the contrast from 1 toTo configure the IP settings Click Basic User User setup window appears To set the user accountCurrently opened web browser will be closed Setup screen To set the date/time System SetupWhen done, click Apply Selected language will be applied To set the display languageTo update the software To check the log informationSelect System Log Log information list appears Click OK to restart the system To reset the systemAll Restores all settings to the default To set the HttpsOverlay Setup To set the textYou can display text on the screen Verified will be displayed Event SetupTo set the event transfer function To test the FTP transfer Click TestSetup screen FTP transfer The image is sent to the specifi ed FTP address To set an alarm imageTo set the alarm input Select Event Motion Motion Detection setup window appearsTo set the motion detection function Motion Detection function will operate on the selected area To set a motion areaNetwork Setup To set the video transfer modeTo set the scheduled transfer To set the Ddns ALC DAY ModeITS GamingVBRVariable Bitrate TerminologyCavlc Bitrate Control CBRConstant BitrateSpecifications 4CIF AI DCRAM DSPDdns SetupHTTPS, SSL, Dhcp ARP, DNS, DDNS, VsipNtsc Http APISDK Frame Rate Ntsc EstimationHPelMPEG4 4CIF FPS 30 FPS 15 FPSMPEG4 VGA 264 VGA MPEG4 CIF 264 CIF Frame Rate PAL 25 FPS 13 FPS MPEG4 VGA Kbps 17 FPS MPEG4 CIF 264 CIF Problem Solution TroubleshootingAlarm Video Transmission must be enabled Verify the settings in the following sequenceNTP must be properly configured Motion Detection Feature must be enabledWe protect your rights with two steps GPL/LGPL Software LicenseGNU General Public License PreambleProgram, and can be reasonably Page Page No Warranty How to Apply These Terms to Your New ProgramsEND of Terms and Conditions Preamble Terms and Conditions Source Code Basic PermissionsProtecting Users Legal Rights From Anti-Circumvention Law Conveying Verbatim Copies Conveying Modified Source VersionsConveying Non-Source Forms Installed in ROM Additional Terms Acceptance Not Required for Having Copies Automatic Licensing of Downstream RecipientsPatents Valid No Surrender of Others FreedomUse with the GNU Affero General Public License END of Terms and Conditions GNU Lesser General Public LicensePreamble Page Page Page Page Page How to Apply These Terms to Your New Libraries No Event Shall the OpenSSL OpenSSL LicenseCopyright C1995-1998 Eric Young Original SSLeay License
Related manuals
Manual 105 pages 12.87 Kb Manual 106 pages 9.51 Kb Manual 104 pages 7.14 Kb Manual 104 pages 6.18 Kb