Auto Low Med High | Samsung AQ18UGFN, AQ24TSBXEUR, AQ18TSBN instruction

Samsung AQ18UGFN, AQ24TSBXEUR, AQ18TSBN, AQ12UGFN, AQ24TSBN, AQ18TSBX, AQ09UGFX Auto Low Med High

Page 11

Press the button to turn on the air conditioner.

Press the button to set the operating mode.

•Each time you press the Mode button, the mode will change in order of Auto, Cool, Dry, Fan and Heat.

Press the	button to set the desired fan speed.

Auto		(Auto)

Cool		(Auto),	(Low),	(Med),	(High)

Dry		(Auto)

Fan		(Low),	(Med),	(High)

Heat		(Auto),	(Low),	(Med),	(High)


Press the	button to adjust the temperature.


Auto		You can adjust the desired temperature by 1°C within the range of 16°C~30°C.

Cool		You can adjust the desired temperature by 1°C within the range of 16°C~30°C.

Dry		You can adjust the desired temperature by 1°C within the range of 18°C~30°C.

Fan		Temperature adjustment is not possible.

Heat		You can adjust the desired temperature by 1°C within the range of 16°C~30°C.

• Air flow can be adjusted manually.(see page 12 for instructions.)

ENGLISH

Image 11

Contents

Page Contents Wall socket Safety precautionsImportant safety symbols and precautions Follow directionsFor Using For Cleaning Operation ranges Checking before useDisplay  09/12/18/24T PowerChecking the name of the parts Main parts  09/12/18/24T Remote controller buttons Checking the remote controllerInserting the batteries Remote controller displayBattery changing time Storing the remote controllerBasic function Low Med High AutoAuto Low Med High Vertical air flow Adjusting the air flow directionUsing the Turbo function Press the Air swing button on the remote controllerPress the Time Up or Time Down button to set the time When the air conditioner is on and in cool/heat modePress the button on the remote controller ModeAdditional options available in On timer mode Setting the On/Off timerPress the On Timer/Off Timer button Turn off automatically Using the Smart Saver functionFrom the moment you have set the timer If the air conditioner is on If the air conditioner is offWhen the air conditioner is turned on Using the Auto Clean functionUsing the Quiet function Opening the panel Cleaning the air conditionerCleaning the indoor unit Cleaning the outdoor unit heat exchangerDry the Air filter in a ventilated area Cleaning the air filterRemoving the Air filter Open the panel and put the Air filter outPeriodical checks Maintaining the air conditionerTroubleshooting Connection Outdoor unit Heat exchanger during Heat mode in winterFlow movement changes. It is normal Included Models Remark General information a place where the air filter can be replaced easily Choosing the installation locationInstalling the unit Power supply line, fuse or circuit breakerModel Where sulfide gas existsOutdoor Unit Top view Side view When installing more than 1 outdoor unitWhen the air outlet is towards the wall  Figure DescriptionAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Tools for test operations Fixing the installation plateOptional accessories Tools required for installation General ToolsConnecting the cable Connecting the assembly cableCable specification Installation Extend the assembly cable if necessaryEach wire is labeled with the corresponding terminal number Pass the pipe through the hole in the wall Smooth the cut edgesCut off the remaining foam insulation Put a flare nut slightly into the pipe and modify the flare Purging the indoor unitCutting or extending the pipe Unscrew the caps at the end of each pipeOuter Diameter Pipe 50 Pa. The joint must be accessible and serviceableCorrect Inclined CrackedCheck for leakage on both side of the drain outlet Drain hose installationChanging direction of the drain hose Two hoses are firmly connected, there is no water leakageEnsure that condensation draining is adequate Purging the connected pipesConnect a drain hose to the drain plug If you use a pipe shorter than 5m Gas service port as seen in the pictureAdding Refrigerant If you use a pipe longer than 5m1975 Please fill in with indelible ink the factory refrigerant charge of the product Leak test with nitrogen before opening valves Performing the gas leak testsTo check for gas leaks on the outdoor unit To check for gas leaks on the indoor unitFixing the outdoor unit in place Then place the indoor unit on the installation plateFixing the indoor unit in place Final Check and Trial Operation Insulation tape to finish How to connect your extended power cablesApply heat to the contraction tube to contract it After tube contraction work is completed, wrap it withMemo Questions or COMMENTS? Air Conditioner

Related manuals

Samsung AQ18UGFN, AQ24TSBXEUR, AQ18TSBN, AQ12UGFN, AQ24TSBN, AQ18TSBX, AQ09UGFX Auto Low Med High

(Auto)

(Auto),

(Low),

(Med),

(High)

(Low),

(Med),

(High)

button to adjust the temperature.