Samsung LT23A750EXL/CI, LT27A950EX/CI manual Troubleshooting, Issues Solutions and Explanations

A Mode Not Supported message

• Set your PC’s output resolution and frequency so they match the resolutions supported by the TV (p.

appears.

20).

PC is always shown on the source list,

• This is normal; “PC” is always shown on the source list, regardless of whether a PC is connected.

even if a PC is not connected.

The video is OK but there is no audio.

• If you are using a HDMI connection, check the audio output setting on your PC.

Picture Quality

First of all, please perform the Picture Test and confirm that your TV is properly displaying test image.

(go to MENU - Support - Self Diagnosis - Picture Test) (p. 45)

If the test image is properly displayed, the poor picture may caused by the source or signal.

The TV image does not look as good as it

• If you have an analogue cable/set top box, upgrade to a digital set top box. Use HDMI or Component

did in the store.

cables to deliver HD (high definition) picture quality.

• Cable/Satellite subscribers: Try HD stations from the channel line up.

• Antenna connection: Try HD stations after performing Auto programme.

✎✎ Many HD channels are up scaled from SD(Standard Definition) contents.

• Adjust the Cable/Set top box video output resolution to 1080i or 720p.

• Make sure you are watching the TV at the minimum recommended distance based on the size and

definition of the signal.

The picture is distorted: macro block error,

• Compression of video contents may cause picture distortion especially in fast moving pictures such

small block, dots, pixelization

as sports and action movies.

• Low signal level or bad quality can cause picture distortion. This is not a TV issue.

• Mobile phones used close to the TV (cca up to 1m) may cause noise in picture on analogue and

digital TV.

Colour is wrong or missing.

• If you’re using a component connection, make sure the component cables are connected to the

correct jacks. Incorrect or loose connections may cause colour problems or a blank screen.

There is poor colour or brightness.

• Adjust the Picture options in the TV menu. (go to Picture Mode / Colour / Brightness / Sharpness)

(p. 29)

• Adjust Energy Saving option in the TV menu. (go to MENU - System - Eco Solution - Energy

Saving) (p. 42)

• Try resetting the picture to view the default picture settings. (go to MENU - Picture - Reset Picture)

(p. 34)

There is a dotted line on the edge of the

• If the picture size is set to Screen Fit, change it to 16:9 (p. 30).

screen.

• Change cable/set top box resolution.

The picture is black and white.

• If you are using an AV composite input, connect the video cable (yellow) to the Green jack of

component input 1 on the TV.

When changing channels, the picture

• If connected with a cable box, please try to reset the cable box. Reconnect the AC cord and wait until

freezes or is distorted or delayed.

the cable box reboots. It may take up to 20 minutes.

• Set the output resolution of the cable box to 1080i or 720p.

3D

The 3D Active Glasses are not working

• Make sure the glasses are turned on.

correctly

• The 3D Active Glasses may not work properly if there is any other 3D product or electronic devices

turned on near the glasses or TV.

• If there is a problem, keep other electronic devices as far away as possible from the 3D Active

Glasses.

The screen seems to flicker slightly when

• You may notice a small amount of screen flickering when watching 3D images under a fluorescent

you watch 3D images.

lamp (50Hz ~ 60Hz), a 3 wavelength lamp, or a strobe light. If this occures, dim the light or turn it off

entirely.

The 3D images don’t look quite right.

• The ideal viewing distance is three times or more the height of the screen.

• We also recommend sitting with viewer’s eyes on a level with the screen

The batteries in the 3D glasses don’t last

• Turn off 3D glasses while not using them. If you leave 3D glasses on, battery lifespan is shortened