Lightolier 1004ICVN instruction sheet B1204 Page 1, FRAME-IN Fig. a

Page 1

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:1004ICV

B1204 Page 1 of 4

INSTALLATION PROCEDURE FOR LOW VOLTAGE

INSULATED CEILING FRAME-IN-KIT 1004ICV, 1004ICVN

NEW CONSTRUCTION

NOTE: I.C. Frame-in Kit may be used in direct contact with insulation.

Fig. A

Fig. B

Fig. C

Fig. D

Fig. E

Fig. F

Frame-In

Wire-In

Swing-Up

Close-In

Snap-On

Push-Up

WARNING: USE ONLY WITH LIGHTOLIER REFLECTOR TRIMS MARKED WITH I.C. LAMPING INFORMATION. USE OF OTHER MANUFACTURERS’ TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD

1.FRAME-IN (Fig. A)

Locate fixture along joist and line up bottom edge of HINGED MOUNTING BAR with the bottom of joist and fasten in place.

5 5/8”

CENTER LINE OF

APERTURE OPENING

6”

Note: Integral nail version available

HINGED MOUNTING BAR

BEND AT HOLE

TAB

 

BEND AT TAB

For suspended ceilings:

•Rotate HINGED BAR ENDS to position shown and fully extend bars.

•Crimp bottom of edge of CHANNEL to prevent rotation of HINGED BAR ENDS.

•Bend NON-HINGED end of mounting bar at featured hole location and extend out.

•Position notched area of MOUNTING BARS onto T-BAR and lock by bending TAB underneath T-BAR BEAD as shown.

•For suspended ceiling, make certain that bottom of Mounting Frame is no higher than 1” above ceiling line.

HINGED BAR ENDS

T-BAR

CHANNEL

FOR JOIST SPACING LESS THAN 16” ON CENTER (TO 12” ON CENTER):

•MOUNTING BAR CHANNELS can be shortened and used as nailing legs in tight spaces. Simply remove INNER BAR from holed CHANNEL, bend CHANNEL at appropriate point and use extra screw to secure it to the joist. (Fig. G)

TAB

Fig. G

®

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

Page 1 Page 2
Image 1
Page 1 Page 2
Contents FRAME-IN Fig. a B1204 Page 1B1204 Page 2 Airseal Installation optionalLamping Fig. H B1204 Page 3Remove Lamp Shield from Lamp Ring Make sure power is off Remove Reflector Trim from ceiling Transformer Replacement Fig. KInstall new Transformer B1204 Page 4

1004ICVN specifications

Lightolier 1004ICVN is a highly versatile and efficient recessed lighting fixture designed to meet a variety of residential and commercial needs. Known for its compact design and innovative features, this product stands out in the world of illumination solutions.

One of the main features of the Lightolier 1004ICVN is its insulation contact rating. The fixture is designed to be installed in ceilings with direct contact with insulation, allowing for greater flexibility in your lighting layout. This makes it an ideal choice for new construction or remodels where a clean, flush look is desired while maintaining compliance with energy efficiency codes.

The fixture is equipped with a robust, high-efficiency reflector that enhances the quality of light output and minimizes glare. This reflector uses advanced lighting technologies to produce an even light distribution, making it ideal for various settings, from living rooms to commercial spaces. The smooth finish of the reflector also aids in maintaining a contemporary aesthetic, blending seamlessly into modern architectural designs.

Another important characteristic of the Lightolier 1004ICVN is its compatibility with a range of light sources, including LED, incandescent, and compact fluorescent bulbs. This flexibility means that users can choose the best lighting solution that meets their specific requirements for brightness and color temperature. The fixture's design also allows for easy bulb replacement, a feature that enhances its practicality and convenience.

The Lightolier 1004ICVN is designed with user-friendly installation features. It includes adjustable hanger bars that facilitate mounting in various ceiling types and ensure a secure fit. This makes the installation process straightforward, even for those who are not lighting professionals.

Moreover, the fixture supports dimming capabilities, allowing users to create the desired ambiance in any space. This is increasingly important as homeowners and businesses look to enhance their environments through controllable lighting solutions.

In summary, the Lightolier 1004ICVN is a forward-thinking recessed lighting solution that combines a sleek design with versatile functionalities. Its compatibility with various light sources, insulation contact rating, light-enhancing reflector, and ease of installation make it a popular choice for both residential and commercial applications. With the growing emphasis on energy efficiency and customizable lighting experiences, the Lightolier 1004ICVN effectively meets the demands of modern lighting projects.
Top Page Image Contents