Chief Manufacturing CM2L40 Adjustments, Display Travel Adjustment, Drive Belt Tension Adjustment

Page 15

Installation Instructions

CM2L40

ADJUSTMENTS

 

Display Travel Adjustment

 

The CM2 is designed to allow the adjustment of both "Extend"

 

and "Retract" display travel limits. The CM2 is shipped set at

 

maximum extension and retraction.

 

There is an upward travel limit adjustment screw and a

 

downward travel limit adjustment screw located on the top right

 

hand side of the mount. (See Figure 25)

 

NOTE:

10 full turns of the "Extend" or "Retract" travel

 

 

 

adjustment screws is equal to 1" of display travel.

 

1.

Turning the "Extend" travel adjustment screw clockwise will

 

 

increase the amount of display upward travel. Turning the

 

 

"Extend" adjustment screw counter-clockwise will decrease

 

 

the amount of display upward travel.

 

2.

Turning the "Retract" travel adjustment screw clockwise will

 

 

decrease the amount of display downward travel. Turning

 

 

the "Retract" adjustment screw counter-clockwise will

 

 

increase the amount of display downward travel.

 

 

 

 

Figure 26

 

 

 

Drive Belt Tension Adjustment

 

 

 

Drive belt tension is preset at the factory and should not need

 

 

 

adjustment during initial mount installation or operation.

 

 

 

However, after extended use it may be necessary to make

 

 

 

minor adjustments to belt tension. (See Figure 27)

 

 

EXTEND

NOTE: If during operation the lift moves slower than normal or

 

 

1

is not raising and lowering smoothly or making unusual

 

 

noise, belt tension may need to be adjusted.

 

 

 

 

 

 

Drive belt tension is adjusted by turning an adjustment screw

 

 

RETRACT

located on the lower back side of the mount using a 3/16" hex

 

 

2

wrench. (See Figure 27)

 

 

 

 

 

 

WARNING: OVERTENSIONING CAN LEAD TO DAMAGE

 

 

 

TO EQUIPMENT! DO NOT overtension! Adjust drive belt

 

 

 

tension in small increments.

 

 

 

Turning the screw clockwise will increase drive belt tension and

 

 

 

counter-clockwise will decrease drive belt tension.

Figure 25

Lift Cable Tension Adjustment

Lift cable tension is preset at the factory and should not need adjustment during initial mount installation. However, after extended use it may be necessary to make minor adjustments.

If there is visible slack in cables or a rattling sound is heard in the area of the cable guides, cable tension may need adjustment.

Cable tension is adjusted by turning an adjustment screw located on the top left hand side of the mount using a hex wrench. (See Figure 26)

Turning the screw clockwise will increase cable tension and counter-clockwise will decrease cable tension.

Figure 27

15

Image 15
Contents CM2L40 Important Warnings and Cautions CM2L40 Installation InstructionsTools Required for Installation Parts ContentsDimensions Tighten Fastener Pencil Mark Pre-Installation Configuration and Adjustments Installation RequirementsInstallation Power Requirements and WiringIf more than 2 of faceplate adjustment is required Display Installation Refer to Adjusting Faceplate Location section, and adjust Shelf Height AdjustmentDetermining Minimum I.D. of Furniture Cable Installation and Routing From Display Cable Mount Installation Lift Cable Tension Adjustment AdjustmentsDisplay Travel Adjustment Drive Belt Tension AdjustmentLift Column Bearing Adjustment Extended Programming Capabilities Normal Operating ModeIR-SE15 Control Codes IR-SE15 ProgrammingAddress Description Connections to be made to 9 pin connector as followsSerial Communications NoneCM2L40 Installation Instructions CM2 Interface Board Hardware InformationDry Contact Closures Other Dry Contact Options Extend Retract with Single SwitchRetract Error Input Voltage Sense External Power SourceVoltage Sense Internal 24V DC Power Source Extend Error InputConnector and Switch Assignments Extend Limit OptionRetract Limit Option SW1 TroubleshootingElevador automatizado para televisor CM2L40 Instrucciones de instalación Advertencias Y Precauciones ImportantesHerramientas Necesarias Para LA Instalación Piezas Funciones de programación avanzadasReferencia del soporte físico del CM2 Dimensions Inches Referencias Requisitos de alimentación y cableado Configuración y ajustes para la instalaciónRequisitos DE Instalación Instalación25 mm Figura Instalación del televisor Ajuste de la altura del estante Cálculo de la altura interna mínima del mueble Figura Cubierta lateral De la guía de cables Instalación y tendido de cablesProveniente del televisor Figura Advertencia EL Soporte Pesa MÁS DE 18 KG Instalación del soporteAjuste de la tensión de la correa de transmisión AjustesAjuste del desplazamiento del televisor Ajuste de la tensión de los cablesRepita los pasos 1 a 3 hasta lograr el movimiento deseado Ajuste de los cojinetes de las columnas de elevaciónModo de operación normal Funciones de programación avanzadasCódigos de control del SE15 Programación del control remoto SE15Conexiones que deben hacerse al conector de 9 pines Comunicaciones en serieIdentificador de producto para el CM2L40 Código de comprobación calculadoCierres de contactos secos Información sobre la placa de interfaz del CM2Posición del conjunto de interruptores Posición del conjunto de conectoresOtras opciones de contactos secos Descenso y ascenso con un solo interruptorDetección de voltaje fuente de alimentación externa Entrada de error de ascenso Entrada de error de descensoAsignación de conectores e interruptores Opción de límite de extensiónOpción de límite de retracción Solución de problemas Иукции П УК ЖЫ Пдупждия И Пджия «И ЭИ ИУКЦИИ»ПЬ. УИ ИК Пжия Элкички К Пини бдвния CM2 ИУЫ, Бдиы ДЛЯ УКИ КПЫДЖИ БИЯ К УК Шинны вмжнти пгммивнияDimensions Inches УЛЫ Бзчия Кнфигция и нтки пд тнвк БИЯ К УКБвния к элктпитнию Элктпвдк Тк кнштн для мнитБл чм н 2 дюм, выплнит лдющ Пдупжди Утнвк мнитТк выты плки Мв бдвния Пдлни минимльны внтнниНтж и пклдк кбля CM2L40 CM2L40 Пджи Утнвк кнштн Тк пмщния мнит CM2L40 Тк нтяжния шн Ттв пдъмГливк п тк ттв пдъм Тк нтяжния пивднг мняЗмыкния «и» кнтктв Шинны вмжнтиПгммивния Бычны жим экплтцииКды пвлния IR-SE15 Пгммивни IR-SE1510 ыдвижни д пдл = 0500107B0D 12 тягивни д пдл = 0500127D0D Плдвтльны пдчи днныКДЯ К Плдльг Уплия Кд идлия CM2L40Змыкния «и» кнтктв CM2L40Вдния б бдвнии интфн плты CM2 Пв плжни Мив пключтл Пв плжни мив ДиннияЫдвижни или бтн пмщни ипльвним днг пключтля Дги винты и кнтктвШибки выдвижния Нтнни итчник питния птянным ткм 24 и дтчикм нпяжнияШибки бтнг пмщния Мжнть гничния выдвижнияИнт гничния бтнг движния Нчния ъмв и пключтл Утнни нипвнтCM2L40 CM2L40 USA/International 800.582.6480877.894.6918

CM2L40 specifications

The Chief Manufacturing CM2L40 is an exemplary product in the realm of LCD and plasma display mounting solutions, designed particularly for commercial and institutional environments. This mount stands out for its robust construction and versatile functionality, catering to a wide range of television sizes and weight capacities.

One of the standout features of the CM2L40 is its exceptional weight capacity, supporting displays up to 400 pounds. This makes it ideal for mounting larger screens that are often required in professional settings such as conference rooms, classrooms, and public venues. The mount’s sturdy design ensures that it can hold heavy displays securely, providing peace of mind for users.

The CM2L40 is engineered with versatility in mind. It offers a variety of mounting options, including fixed, tilting, and full-motion capabilities. This adaptability allows users to position their displays at optimal viewing angles, enhancing the overall viewing experience. The tilting feature is particularly beneficial in environments where viewers might be seated below the screen, as it helps reduce glare and provides a better line of sight.

Installation of the CM2L40 is made simple with its user-friendly design. The mount includes a quick-release mechanism for easy access to the display, enabling effortless adjustments and maintenance. Additionally, the mount is compatible with various VESA patterns, offering flexibility for different screen brands and sizes.

A key technology used in the CM2L40 is its integrated cable management system. This feature helps to organize and conceal wiring, resulting in a cleaner and more professional appearance. By minimizing clutter, the mount contributes to a more aesthetically pleasing setup, which is essential in commercial environments.

Durability is another hallmark of the Chief Manufacturing CM2L40. Constructed from high-quality materials, it is designed to withstand the rigors of daily use in demanding environments. Its powder-coated finish not only enhances its visual appeal but also protects it from scratches and corrosion.

Overall, the Chief Manufacturing CM2L40 is an outstanding choice for anyone in need of a heavy-duty mount solution. Its combination of strength, versatility, and user-friendly features make it a smart investment for commercial applications, ensuring that display technology can be utilized effectively and stylishly. Whether for presentations, lectures, or digital signage, the CM2L40 provides a reliable platform for any large display need.