Chief Manufacturing CM2L40 installation instructions Shelf Height Adjustment

Page 9

Installation Instructions

 

 

 

 

CM2L40

NOTE: Verify that there is at least 1" of clearance between

 

 

 

 

 

bottom of display and mount base.

 

 

 

 

3.

If there is less than 1" of clearance, remove the display and

 

 

 

 

 

refer to Adjusting Faceplate Location section, and adjust

 

 

 

 

 

display height accordingly.

 

 

 

 

 

NOTE: Holes are provided in the faceplate for use with a

 

 

 

 

 

padlock or similar locking device, if desired. In addition,

 

 

 

 

 

the pin and nut may be removed from the upper holes

 

 

 

 

 

and moved to the lower holes for use as a more

 

 

5

Top of Display

 

permanent locking device. (See Figure 10)

 

 

 

 

 

 

 

 

Shelf Height Adjustment

 

 

 

 

 

After the CM2 has been properly configured for the display and

 

 

 

 

the display installed, the shelf height needs to be adjusted to

 

 

 

 

the top of the display.

 

 

 

 

 

To set shelf height:

 

 

 

 

 

1. Using the remote control, raise lift until locknuts securing

 

 

 

 

 

right and left shelf adjustment brackets can be accessed.

 

 

 

 

 

1

 

 

 

 

 

 

 

Display removed

 

 

Figure 13

 

 

 

5.

Lower shelf and shelf mounting brackets down until shelf is

 

 

for clarity

 

 

 

1/4" (6.5mm) above top of display.

 

 

 

 

 

 

 

 

 

6. Tighten four nuts to secure shelf mounting bracket in

 

 

 

 

position.

 

 

 

 

 

 

WARNING: IMPROPER INSTALLATION CAN LEAD TO

 

 

 

 

SEVERE PERSONAL INJURY OR DAMAGE TO

 

 

 

 

EQUIPMENT! Make sure all four nuts are tight before

 

 

 

 

continuing installation!

 

 

 

Figure 11

 

 

 

 

 

2. Loosen four nuts securing right and left hand shelf

 

 

 

 

 

adjustment brackets to faceplate mounting bracket.

 

 

1/4" (6.5mm) min.

3.

Slide shelf adjustment brackets upward until top of brackets

 

 

 

 

 

are positioned higher than top of display. (See Figure 12)

 

 

 

 

 

 

Display and Faceplate

 

 

 

 

 

3

removed for clarity

 

5

 

 

 

2

 

 

 

 

 

 

 

X4

 

6

x 4

 

 

 

 

 

 

 

 

Figure 12

 

 

 

 

 

4.

Re-install shelf assembly to shelf adjustment brackets by

 

 

 

 

aligning studs in shelf bracket with clips in shelf adjustment

Figure 14

brackets.

 

9

Image 9
Contents CM2L40 Important Warnings and Cautions CM2L40 Installation InstructionsTools Required for Installation Parts ContentsDimensions Tighten Fastener Pencil Mark Installation Installation RequirementsPower Requirements and Wiring Pre-Installation Configuration and AdjustmentsIf more than 2 of faceplate adjustment is required Display Installation Refer to Adjusting Faceplate Location section, and adjust Shelf Height AdjustmentDetermining Minimum I.D. of Furniture Cable Installation and Routing From Display Cable Mount Installation Display Travel Adjustment AdjustmentsDrive Belt Tension Adjustment Lift Cable Tension AdjustmentLift Column Bearing Adjustment Extended Programming Capabilities Normal Operating ModeIR-SE15 Control Codes IR-SE15 ProgrammingSerial Communications Connections to be made to 9 pin connector as followsNone Address DescriptionCM2L40 Installation Instructions CM2 Interface Board Hardware InformationDry Contact Closures Other Dry Contact Options Extend Retract with Single SwitchVoltage Sense Internal 24V DC Power Source Voltage Sense External Power SourceExtend Error Input Retract Error InputConnector and Switch Assignments Extend Limit OptionRetract Limit Option SW1 TroubleshootingElevador automatizado para televisor CM2L40 Instrucciones de instalación Advertencias Y Precauciones ImportantesHerramientas Necesarias Para LA Instalación Piezas Funciones de programación avanzadasReferencia del soporte físico del CM2 Dimensions Inches Referencias Requisitos DE Instalación Configuración y ajustes para la instalaciónInstalación Requisitos de alimentación y cableado25 mm Figura Instalación del televisor Ajuste de la altura del estante Cálculo de la altura interna mínima del mueble Figura Cubierta lateral De la guía de cables Instalación y tendido de cablesProveniente del televisor Figura Advertencia EL Soporte Pesa MÁS DE 18 KG Instalación del soporteAjuste del desplazamiento del televisor AjustesAjuste de la tensión de los cables Ajuste de la tensión de la correa de transmisiónRepita los pasos 1 a 3 hasta lograr el movimiento deseado Ajuste de los cojinetes de las columnas de elevaciónModo de operación normal Funciones de programación avanzadasCódigos de control del SE15 Programación del control remoto SE15Identificador de producto para el CM2L40 Comunicaciones en serieCódigo de comprobación calculado Conexiones que deben hacerse al conector de 9 pinesPosición del conjunto de interruptores Información sobre la placa de interfaz del CM2Posición del conjunto de conectores Cierres de contactos secosOtras opciones de contactos secos Descenso y ascenso con un solo interruptorDetección de voltaje fuente de alimentación externa Entrada de error de ascenso Entrada de error de descensoAsignación de conectores e interruptores Opción de límite de extensiónOpción de límite de retracción Solución de problemas Иукции П УК ЖЫ Пдупждия И Пджия «И ЭИ ИУКЦИИ»ПЬ. УИ ИК Пжия Элкички К ДЖИ ИУЫ, Бдиы ДЛЯ УКИ КПЫБИЯ К УК Шинны вмжнти пгммивния Пини бдвния CM2Dimensions Inches УЛЫ Бзчия Бвния к элктпитнию Элктпвдк БИЯ К УКТк кнштн для мнит Кнфигция и нтки пд тнвкБл чм н 2 дюм, выплнит лдющ Пдупжди Утнвк мнитТк выты плки Мв бдвния Пдлни минимльны внтнниНтж и пклдк кбля CM2L40 CM2L40 Пджи Утнвк кнштн Тк пмщния мнит CM2L40 Тк нтяжния шн Ттв пдъмГливк п тк ттв пдъм Тк нтяжния пивднг мняПгммивния Шинны вмжнтиБычны жим экплтции Змыкния «и» кнтктвКды пвлния IR-SE15 Пгммивни IR-SE15КДЯ К Плдльг Уплия Плдвтльны пдчи днныКд идлия CM2L40 10 ыдвижни д пдл = 0500107B0D 12 тягивни д пдл = 0500127D0DВдния б бдвнии интфн плты CM2 CM2L40Пв плжни Мив пключтл Пв плжни мив Динния Змыкния «и» кнтктвЫдвижни или бтн пмщни ипльвним днг пключтля Дги винты и кнтктвШибки выдвижния Нтнни итчник питния птянным ткм 24 и дтчикм нпяжнияШибки бтнг пмщния Мжнть гничния выдвижнияИнт гничния бтнг движния Нчния ъмв и пключтл Утнни нипвнтCM2L40 CM2L40 USA/International 800.582.6480877.894.6918

CM2L40 specifications

The Chief Manufacturing CM2L40 is an exemplary product in the realm of LCD and plasma display mounting solutions, designed particularly for commercial and institutional environments. This mount stands out for its robust construction and versatile functionality, catering to a wide range of television sizes and weight capacities.

One of the standout features of the CM2L40 is its exceptional weight capacity, supporting displays up to 400 pounds. This makes it ideal for mounting larger screens that are often required in professional settings such as conference rooms, classrooms, and public venues. The mount’s sturdy design ensures that it can hold heavy displays securely, providing peace of mind for users.

The CM2L40 is engineered with versatility in mind. It offers a variety of mounting options, including fixed, tilting, and full-motion capabilities. This adaptability allows users to position their displays at optimal viewing angles, enhancing the overall viewing experience. The tilting feature is particularly beneficial in environments where viewers might be seated below the screen, as it helps reduce glare and provides a better line of sight.

Installation of the CM2L40 is made simple with its user-friendly design. The mount includes a quick-release mechanism for easy access to the display, enabling effortless adjustments and maintenance. Additionally, the mount is compatible with various VESA patterns, offering flexibility for different screen brands and sizes.

A key technology used in the CM2L40 is its integrated cable management system. This feature helps to organize and conceal wiring, resulting in a cleaner and more professional appearance. By minimizing clutter, the mount contributes to a more aesthetically pleasing setup, which is essential in commercial environments.

Durability is another hallmark of the Chief Manufacturing CM2L40. Constructed from high-quality materials, it is designed to withstand the rigors of daily use in demanding environments. Its powder-coated finish not only enhances its visual appeal but also protects it from scratches and corrosion.

Overall, the Chief Manufacturing CM2L40 is an outstanding choice for anyone in need of a heavy-duty mount solution. Its combination of strength, versatility, and user-friendly features make it a smart investment for commercial applications, ensuring that display technology can be utilized effectively and stylishly. Whether for presentations, lectures, or digital signage, the CM2L40 provides a reliable platform for any large display need.