Appendix
General Troubleshooting
|
| Applies to |
|
| |
|
|
|
|
|
|
|
|
|
|
| Dimmer |
Symptom | Solution(s) |
| Foggers | Controller | s& |
Lights | & Snow | s | Chaser | ||
|
|
|
|
|
|
Auto shut off | Check fan thermal switch reset | 9 |
|
|
|
|
|
|
|
|
|
Beam is very dim or not | Clean optical system or replace lamp | 9 |
|
|
|
bright | Check 220/110v switch for proper setting |
|
|
|
|
Breaker/Fuse keeps | Check total load placed on device |
|
|
| 9 |
blowing |
|
|
|
|
|
Chase is too slow | Check users manual for speed adjustment | 9 |
| 9 | 9 |
|
|
|
|
|
|
Device has no power | Check for power on Mains. | 9 |
| 9 | 9 |
| Check device’s fuse. (internal and/or external) |
|
|
|
|
Fixture is not responding | Check DMX Dip switch settings for correct addressing | 9 |
|
|
|
| Check DMX cables |
|
|
| |
| Check polarity switch settings |
|
|
|
|
Fixture is on but there is | Make sure you have the correct audio mode on the control |
|
|
|
|
no movement to the | switches. If audio provided via ¼” jack, make sure a live audio | 9 |
| 9 | 9 |
audio | signal exists |
|
|
|
|
| Adjust sound sensitivity knob |
|
|
|
|
Lamps cuts off | Possible bad lamp or fixture is overheating. | 9 |
|
|
|
sporadically | Lamp may be at end of its life. |
|
|
|
|
Light will not come on | Some discharge lamps require a cooling off period before the | 9 |
|
|
|
after power failure | electronics in the fixture can kick start it again, wait 5 to 10 |
|
|
| |
| minutes before powering up |
|
|
|
|
Loss of signal | Use only DMX cables |
|
|
|
|
| Install terminator | 9 | 9 | 9 | 9 |
| Note: Keep DMX cables separated from power cables or black |
|
|
|
|
| lights. |
|
|
|
|
Motor movements are | Possible bad motor driver or sensors | 9 |
| 9 |
|
jerky or jumpy | Check polarity switch on controller |
|
|
|
|
Moves slow | Check 220/110v switch for proper setting | 9 |
|
|
|
|
|
|
|
|
|
No flash | 9 |
|
|
| |
|
|
|
|
|
|
No light output | Check slip ring & brushes for contact | 9 |
|
|
|
| Install bulb |
|
|
| |
| Call service technician |
|
|
|
|
|
|
|
|
|
|
Relay will not work | Check reset switch |
|
|
| 9 |
| Check cable connections |
|
|
|
|
Remote does not work | Make sure connector is firmly connected to device | 9 | 9 |
|
|
|
|
|
|
|
|
Stand alone mode | All Chauvet lighting fixtures featuring | 9 |
|
|
|
| not require additional settings, simply power the fixture and it |
|
|
| |
| will automatically enter into this mode |
|
|
|
|
|
|
|
|
|
|
Unit wobbles when | Check for damages possibly incurred during shipping | 9 |
|
|
|
rotating |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
8 | Revision: |