Oreck RORB600 Sealed Hard Wood Floor Applications, Refinishing, Surface Cleaning Sealed Floors

Page 7

E N G L I S H

3.Dip mop in stripping solution and apply to floor in a 6 ft by 6 ft area. Apply along baseboard edges first or where there is a wax or dirt build-up.

4.Let solution stand for 5 minutes, scrub floor with Orbiter® Multi-Floor Machine and the brown strip pad. Use interior circle (donut hole) from the brown strip pad to reach in corners and around door jambs.

5.To pick up dirty solution, use a mop or wet-dry vacuum. DO NOT ALLOW STRIPPING SOLUTION TO DRY ON FLOOR.

6.Repeat steps 3-5 until the entire floor is completely stripped.

7.Rinse area TWICE with clean water and clean mop. Pick up water with mop or wet-dry vacuum.

8.Allow floor to dry before applying new floor finish.

Precautions:

1.Do not flood the floor with stripping solution or allow solution to dry before pick-up.

2.Use clean mop for final rinse.

3.Change rinse water frequently.

4.Use damp cloth to wipe off any splashes on walls or furniture.

Refinishing

This procedure can be used on most types of hard floor surfaces, EXCEPT WOOD & STONE FLOORS.

Equipment and Material Required:

•Orbiter® Multi-Floor Machine

•Black Drive Pad Holder

•White Polish Pad or Lamb’s Wool Bonnet

•Floor finish liquid

•Clean string mop, 16-20 oz. size

•Bucket and wringer

•Disposable plastic bag

Procedure:

1.Place disposable bag inside of bucket with wringer. This will protect floor finish from being contaminated and chemical residue remaining in bucket.

2.Pour quart size container of floor finish into the disposable bag. Amount of floor finish depends on size of floor area to be covered and number of coats to be applied.

3.ONLY dip the mop tip into the floor finish and wring out lightly. Avoid dripping floor finish or splashing on walls.

4.Apply floor finish in thin even coats. Apply FIRST COAT of floor finish along baseboard edges and cover remaining floor area in an left-right direction.

HINT: Only the first coat of floor finish needs to be applied to baseboard edges.

5.Allow floor finish to dry for 20 minutes before applying a second coat.

6.Apply the second coat of floor finish 1 tile width from baseboard. Application should be in a crossing direction to the preceding coat.

7.Additional coats (3 and 4) of floor finish should be applied to achieve the level of appearance desired. Four coats of floor finish will provide extra protection to the floor surface.

8.Allow 24 hours for floor finish to harden before buffing.

9.Buff floor to higher shine using Orbiter® Multi-Floor Machine and white polish pad or lamb’s wool bonnet.

Precautions:

1.When using NEW mops to apply floor finish, make sure to rinse mop first. Foreign chemicals will affect the floor finish.

2.Completely submerging mop head into the floor finish is a waste of product.

3.Turn mop over frequently for even distribution of floor finish.

4.Do not allow mop to become dry; this will cause streaking.

5.Apply floor finish in thin even coats.

6.Do NOT pour floor finish directly on the floor and attempt to spread evenly. This will cause dark spots and delay drying time.

Sealed Hard Wood Floor

Applications

Surface Cleaning Sealed Floors

This procedure is for polyurethane-sealed hard wood floors, not waxed hard wood floors.

Timberworks® Floor Cleaner restores the natural beauty of all your hard flooring (not for use on stone, tile, or waxed floors). It safely and effectively removes the dirt, scuffs and grime from your floors to reveal their original and beautiful luster.

Equipment and Material Required:

•Orbiter® Multi-Floor Machine

•Black Drive Pad Holder

•White Terrycloth Bonnet

•Timberworks® Floor Cleaner

•White Polish Pad (optional)

Procedure:

To clean hard flooring, including polyurethane-coated wood, laminate, vinyl and linoleum floors, use the Timberworks® Floor Cleaner and the Orbiter® Multi-Floor Machine with the white terrycloth bonnet. Vinyl and laminate flooring can be polished to a higher luster using the white polish pad after cleaning.

1.Lightly mist a 6 ft by 6 ft area with Timberworks® Floor Cleaner (a little goes a long way).

2.Clean the treated area with the Orbiter® Multi-Floor Machine and the white terrycloth bonnet.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Visit ONE of OUR Over 450 Store Locations OrbiterTable of Contents Safety General InformationGrounding Information WarrantyGetting Started Customer ServiceAttaching Accessories IntroductionCarpet and Area Rug Applications Scrubbing Surface CleaningDo not Allow Cleaning Solution to DRY on Floor Laminate, Vinyl Linoleum Floor ApplicationsSealed Hard Wood Floor Applications Surface Cleaning Sealed FloorsRefinishing Waxed Hard Wood Floor Applications Surface Cleaning and Waxing Waxed Hard Wood FloorsDeep Cleaning Tile Floor ApplicationsStone Floor Applications Light CleaningMarble Restoration Concrete and Asphalt Applications AccessoriesSand Screens Maintenance TroubleshootingUser Maintenance BrushesBounces Troubleshooting GuideFloor Machine Will not runInformations Général ES ET DE Sécurité Informations General es et de SécuritéGarantie Informations de mise à la terreAvertissement Fixation des accessoires Service à la clientèlePour commencer Guidage de la machine pour sols Démontage des accessoiresApplications sur Moquettes et tapis Mise en marche/arrêt de la machine pour solsRécurage Applications sur sols Laminés, vinyle et linoléumNettoyage à la bonnette Nettoyage de surfacePrécautions Laissez PAS LA Solution Nettoyante Sécher SUR LE SOLDécapage RestaurationParquets en bois Applications sur sols en Bois dur imprégnéNettoyage de surface de parquet imprégné Passage à la toile abrasiveNettoyage en profondeur Applications sur Sols carrelésApplications sur sols en Bois dur ciré Nettoyage de surface et cirage de parquets cirésÉlimination de l’huile et de la saleté Applications sur sols en pierreApplications sur béton Et asphalte Restauration du marbreTampons AccessoiresGénéraux BonnettesSoins de votre machine pour sols Oreck Entretien et dépannageBrosses Toiles abrasivesGuide de Dépannage Aplicación EN Pisos Encerados Información General y De SeguridadGarantía Información para la puesta a tierraAtencion Instalación de accesorios IntroducciónPara empezar Servicio al ClienteManejo de la Máquina para Pisos Aplicación en alfombras TapetesExtracción de accesorios Encendido y apagado de la Máquina para PisosFregado Aplicación en pisos laminados Vinílicos y de linóleoLimpieza con bonete Limpieza superficialPrecauciones DesprendimientoReacabado Permita QUE LA Solución DE Limpieza SE Seque Sobre EL PisoPisos de madera Aplicación en pisos sellados De madera duraLimpieza superficial de pisos sellados Pulido con mallas abrasivasLimpieza profunda Aplicación en pisos De baldosasAplicación en pisos Encerados de madera dura Limpieza superficial y encerado de pisos de madera duraEliminación de aceite y suciedad Aplicación en pisos de piedraAplicación en concreto Asfalto Restauración de mármolAlmohadillas AccesoriosDe uso general BonetesCuidado de su Máquina Orbiter Multi-Floor Mantenimiento y Localización de fallasCepillos Mallas abrasivasGuía Para Identificación De Problemas

RORB600, RORB400, RORB550, RORB700 specifications

Oreck is renowned for its lightweight and powerful vacuum cleaners, and the RORB series showcases this legacy through its innovative designs and advanced features. Among the popular models in this lineup are the RORB400, RORB700, RORB550, and RORB600, each offering unique characteristics tailored to meet diverse cleaning needs.

The Oreck RORB400 stands out with its impressive maneuverability and ease of use. Weighing only 8 pounds, it is designed for simple handling, making it a favorite among users who prioritize convenience. Its powerful motor provides a deep clean, efficiently removing dirt and debris from various surfaces. The RORB400 features Oreck’s proprietary sanitizing technology, which employs a combination of pre-filter and a HEPA filter that captures 99.97% of allergens as small as 0.3 microns, promoting a healthier home environment.

Transitioning to the RORB700, this model elevates cleaning efficiency with its dual-level suction system. The RORB700 is equipped with a smart sensor that automatically adjusts the suction power based on the type of surface being cleaned, ensuring optimal performance on carpets, hardwood, and tile. This model also integrates a large-capacity dustbin that reduces the frequency of emptying, making it perfect for larger spaces.

The Oreck RORB550 introduces a multi-layer filtration system that not only captures allergens but also blocks odors, making it ideal for households with pets. Additionally, its easy-to-reach controls and lightweight design facilitate seamless use for everyday cleaning tasks. The RORB550's ergonomic handle further enhances comfort, allowing users to clean for extended periods without strain.

Lastly, the RORB600 brings additional technology to the table with its built-in smart navigation system. This model employs sensors to map out rooms and avoid obstacles, allowing for efficient cleaning patterns. Its quiet operation ensures that users can maintain cleanliness without disturbing their household or neighbors. The RORB600 also features extended runtime capabilities, making it suitable for larger homes that require thorough cleaning sessions.

In summary, the Oreck RORB series, including the RORB400, RORB700, RORB550, and RORB600, offers a range of lightweight, user-friendly vacuum cleaners packed with advanced technologies and features. From enhanced filtration systems to intelligent navigation mechanisms, these models deliver exceptional cleaning performance tailored to the modern user’s needs.
Top Page Image Contents