Heath Zenith 2LBL9 Receiver Information, Halogen Security Light 2LBN1, Lamp Modes

Page 5

Receiver Information

All receivers have the following features and ratings:

•Rated for 120VAC/60Hz supply voltage.

•Uses existing wiring.

•Fits standard single gang junction box (wall switch only).

•Not for use with Compact Fluorescent bulbs.

•When first turned on wait 15 seconds.

Halogen Security Light (2LBN1)

Features and Ratings:

• Up to 200 Watt maximum halogen load

(up to 100 Watt maximum halogen,

per lampholder).

•Use only T3, 100W (max.) tungsten halogen 120 VAC lamps.

•Minimal wiring required.

•Install fixture in accordance with local codes.

Lamp Modes

There are three lamp modes (light turn-on effects) available when motion is detected:

•NORMAL or - Light instantly comes on.

•SOFT - Light starts dim and gradually increases to full brightness. Light gradually dims to half-bright, pauses, and then continues dimming to off when motion is no longer detected and after selected ON-TIME.

•FLASH - Light flashes on then off twice before turning on full brightness.

WARNING: Turn power off at the fuse or circuit breaker.

1.Remove the existing light fixture.

2.Install the mounting strap as shown using two screws that fit your junction box.

Note: The plastic hanger can be used to hold the fixture while wiring. Thread the small end of the plastic hanger through the hole in the center of the cover plate. Insert the small end into one of the slots on the mounting strap.

3.Set the LAMP MODE switch to the desired light turn-on effect (Normal, Soft, Flash).

4.Route the wires from the light receiver through the large gasket holes.

5.Twist the junction box wires and fixture wires together as shown.

Secure with UL approved wire connectors.

6.Align the cover plate and cover plate gasket. Secure with mounting bolt.

7.

Push the rubber plug firmly into place.

 

 

 

8.

Not intended for waterproof junction boxes. Fixture should be

 

 

surface mount only. Caulk the wall plate mounting surface with

 

 

silicone weather sealant.

 

 

 

 

 

9.

Adjust the lamp holders by loosening the lock nuts. Note: Do

 

 

not rotate the lamp holders more than 180° from the factory

ENGLISH

 

setting.

 

 

 

 

 

 

 

Caution: To avoid water damage and electrical shock,

 

keep lamp holders 30° below horizontal.

 

 

 

10.

Insert halogen bulb (see Bulb Installation) up to rated wattage

 

 

into module.

 

 

 

 

 

 

 

 

Caution: Do not exceed the maximum load limits listed

 

 

above.

 

 

 

 

 

 

 

11.

Check operation. Activate transmitter being used with receiver

 

 

(see transmitter instructions).Asignal will be sent to the receiver

 

 

 

 

to turn the receiver ON or OFF.

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: Risk of fire. Do not aim the lamps at a

 

 

combustible surface within 3 ft. (1 m).

 

 

 

 

 

 

 

 

 

 

 

 

Mounting

 

 

 

 

 

 

 

 

 

White to

 

Black to

 

Rubber

 

Strap

 

 

 

 

 

White

 

Black

 

 

 

 

 

 

 

Plug

 

 

 

 

 

 

 

 

 

Gasket Mounting

Bolt

Junction box ground wire to green

ground screw on fixture.

Wiring Halogen Security Light

Continued

598-1326-01

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Your particular product FeaturesFor USE only with 120 volt incandescent or halogen bulbs Lighting, or any other electrical devicesCode Switch Locations Code SettingsExample 1 Code Settings, System Example 2 Code Settings, SystemInstalling Batteries Select Night or 24 Hour ModeInstalling Motion Sensor Motion SensorAdjusting Motion Sensor Coverage Check Operation and AdjustmentMotion Sensor Coverage Area Motion Sensor ControlsReceiver Information Wiring Halogen Security LightHalogen Security Light 2LBN1 Lamp ModesBulb Installation White Wiring FloodlightFloodlight 2LBL9 Symptom Possible Cause Solution Troubleshooting GuideYear limited warranty Regulatory InformationPágina CaracteristicasAdvertencias Ubicaciones DE LOS Interruptores DE Circuito Impreso Calibraciones DEL CódigoEjemplo 1 Calibraciones del código, sistema Ejemplo 2 Calibraciones del código, sistemaInstalación del Detector de Movimiento Detector DE MovimientoSeleccione modo nocturno o modo de 24 horas Instalación de las bateríasControles del Detector de Movimiento de Revisión de la operación y de la regulaciónÁrea de Cobertura del Detector de Movimiento de Sensibilidad del Detector de MovimientoLUZ Halógena DE Seguridad 2LBN1 Información DEL ReceptorFases De Lámpara Cableado de la luz halógena de seguridadCuidado Para evitar los peligros de incendio o Quemazón Instalación de bombillaAdvertencia Riesgo de incendio. No apunte Reflector 2LBL9Tapón de Negro CauchoInformación Regulatoria Guía de Análisis de AveríasSíntoma Causa Probable Solución Garantía limitada a un 1 añoVotre produit CaractéristiquesDu guide de référence Réglage DES Codes Emplacement DES MICRO-INTERRUPTEURSExemple 1 Réglage des codes, System Exemple 2 Réglage des codes, systèmeSélection du mode de nuit ou du mode 24 heures Installation Du Détecteur De MouvementInstallation des piles Détecteur DE MouvementVérification du fonctionnement et du réglage Commandes du détecteur de mouvement surZone de couverture du détecteur de mouvement sur Sensibilité du détecteur de mouvementLuminaire DE Sécurité Halogène 2LBN1 Informations SUR LE RécepteurModes D’Éclairage Raccordement du luminaire de sécurité à halogène SuiteDincendie Installation De L’ampouleCâblage du projecteur Projecteur 2LBL9Guide DE Dépannage Symptôme Cause Possible SolutionRenseignements de règlements Garantie limitée d’un an

2LBN1, 2LBL9 specifications

Heath Zenith is a renowned brand in the home lighting and security industry, and their models 2LBL9 and 2LBN1 are standout products that exemplify their commitment to quality and innovation. These motion-sensing outdoor lights are designed for convenience, security, and energy efficiency, making them ideal for both residential and commercial applications.

The Heath Zenith 2LBL9 features a sleek and modern design, tailored to fit seamlessly into various architectural styles. With a robust construction, it withstands various weather conditions, ensuring durability and longevity. This model incorporates a powerful motion sensor that detects movement within a specified range, offering an effective security solution for homeowners. When the sensor is triggered, the light illuminates automatically, enhancing visibility and deterring unwanted intruders.

Similarly, the 2LBN1 model shares many of the same features but introduces additional functionalities. One of its standout characteristics is the adjustable time and sensitivity settings. Users can customize the duration the light stays on after detecting movement, ranging from a few seconds to several minutes. The sensitivity can also be fine-tuned, allowing it to detect motion from varying distances, making it adaptable to different environments such as driveways, backyards, and pathways.

Both models employ energy-efficient LED technology, significantly reducing energy consumption compared to traditional incandescent bulbs. This design not only helps in lowering electricity bills but also extends the lifespan of the lights, providing reliable performance over many years.

In addition, these models are equipped with a dusk-to-dawn feature, automatically turning on at sunset and off at sunrise. This ensures that your property remains illuminated during nighttime without requiring manual intervention.

The installation process is straightforward, designed to accommodate users with varying levels of DIY experience. Both models come with clear instructions, making them easy to mount on walls or ceilings in outdoor areas.

Overall, the Heath Zenith 2LBL9 and 2LBN1 motion-sensing lights are excellent choices for anyone looking to enhance their outdoor security while also benefiting from energy-efficient lighting solutions. With their advanced features and reliable performance, they stand out as top contenders in the market of outdoor lighting solutions.
Top Page Image Contents