MODEL NUMBER DESCRIPTION
TABLE 2 |
|
|
|
|
|
|
|
|
|
|
| |
2 | 20 | 21 | 01 | A9 |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Code Control Options (Factory Installed) | ||
|
|
|
|
|
|
|
|
|
| A9 | = | |
|
|
|
|
|
|
|
|
|
| A3 | = | |
|
|
|
|
|
|
|
|
|
| A4 | = | |
|
|
|
|
|
|
|
|
|
| A5 | = | |
|
|
|
|
|
|
|
|
|
| A6 | = | |
|
|
|
|
|
|
|
|
|
| A7 | = | |
|
|
|
|
|
|
|
| Painted | Anodized | |||
|
|
|
|
|
|
|
| 68 = Almond | 07 = Bronze | |||
|
|
|
|
|
|
|
| 02 = White | 10 = Clear | |||
|
|
|
|
|
| Code |
| Voltage/Phase | ||||
|
|
|
|
|
| 21 = 208/1 | 23 = 208/3 | 31 = 240/1 41 = 277/1 73 = 480/3 | ||||
|
|
|
| Code Wattage (See Table) |
|
|
| |||||
|
| Code | Length |
|
|
|
|
|
|
| ||
|
| 2 = 2 ft. | 3 = 3 ft. | 4 = 4 ft. | 5 = 5 ft. 6 = 6 ft. | |||||||
Type |
|
|
|
|
|
|
|
|
|
|
| |
Architectural Cabinet Convection Heater |
|
|
|
|
| |||||||
INSTALLATION
WARNING: Hazard of Electric Shock. Disconnect all power before installing heater.
WARNING: Hazard of Electric Shock. Any installa- tion involving electric heaters must be effectively grounded in accordance with the National Electrical Code to eliminate shock hazard.
WARNING: Hazard of Fire.
1.Do not install heaters against any highly com- bustible surfaces such as low density cellulose fibre.
2.Do not locate heater below electrical conve- nience receptacles.
3.Do not store or use gasoline or flammable liq- uids in the vicinity of the heaters.
WARNING: Hazard of Fire. Keep electrical cords, drapes, rugs and other furnishings away from the heater. The normal operating temperatures of cab- inet convectors are relatively high. Proper opera- tion requires free circulation of room air through the heating element.
Installation Wall
1.Unpack the heater from the carton and remove the front panel. Note: The front panel screws are recessed at the bottom of the top front panel at each end of the heater. (Figure 2) Remove top front panel by pulling down to disengage from top of heater. To remove the bottom front panel, remove screws as shown in Figure 3. Pull bottom front panel by pulling upward to disen- gage from bottom of heater.
2.Remove the desired terminal box covers and wire supply knockouts from the terminal box area.
3.Determine the correct mounting height, and scribe or snap a level line on the wall to maintain each heater back plate in a horizontal alignment, when mounting.
4.Mount the back plate to the wall using suitable fasteners (pro- vided by customer) using the scribed line on the wall to keep the heater level.
TIP: Should the wall surface be uneven, secure the heater back panel to the high spots. This will avoid a distorted appearance.
5.Proceed to the wiring instructions.
Recessed Wall
Note: The use of a ALTB Trim kit is strongly recommended when recessing the heater.
A recess opening dimension of
The heater may be recessed up to a depth of
Top Panel
Screws
Figure 2
Bottom
Panel
Screws
Figure 3