Desa Tech SL30NT installation manual Connecting to GAS Supply, Installation Items Needed

Page 11

OWNER’S MANUAL

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: This appliance re- quires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.

Installation Items Needed

Before installing heater, make sure you have the items listed below.

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•equipment shutoff valve *

•test gauge connection *

•sediment trap

•tee joint

•pipe wrench

* A CSA design-certified equipment shutoff

valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Pur-

Installation must include a equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 18).

IMPORTANT: Install equipment shutoff valve in an accessible location. The equip- ment shutoff valve is for turning on or shutting off the gas to the appliance.

Back Stove

 

Panel

 

Product

Back View

Identification

 

Label

 

Side View

Gas Log

Front

Heater

 

of

Gas Inlet

Stove

Connection

Unit

Access

 

Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

WARNING: Use pipe joint seal- ant that is resistant to liquid pe- troleum (LP) gas.

We recommend that you install a sediment trap in supply line as shown in Figure 18. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contami- nants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

chase the optional CSA design-certified

equipment shutoff valve from your dealer.

See Accessories, page 19.

Figure 17 - Gas Regulator Location and Gas Line Access Into Stove Cabinet

The gas inlet connection for the stove heater is located on the lower right-hand side of the stove when viewed from the front of the unit. The gas connection can be made either through the bottom right side or through the lower back opening as illustrated in Figure

17.Make sure gas log heater is secured to the stove cavity assembly.

WARNING: Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

From Gas Meter (5" W.C.** to 10.5" W.C. Pressure)

Sediment

 

Tee Joint

 

 

 

Pipe

Trap

 

Nipple

 

 

 

 

 

 

Cap

CSA Design-Certified

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved Flexible Gas Hose (if allowed by local codes)

Gas

Regulator

3" Minimum

CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas vol- ume to heater. If pipe is too small, undue loss of volume will occur.

Figure 18 - Gas Connection

*Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 19.

**Minimum inlet pressure for purpose of input adjustment.

Continued

104463

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualVENT-FREE Natural GAS Stove Heater Safety InformationOperation Product Identification Product FeaturesSafety Pilot Local CodesConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside BuildingCombustibles Vent-Free Operation Only InstallationCheck GAS Type Clearances toStove bottom Legs Amity models include leg leveler bolts Stove Cavity AssemblyBack panel see Installing Gas Log Washers to reattach back panel later Installing GAS LOG Heater Into StoveInstallation Items Needed Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections To Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Heater Lighting InstructionsInspecting Burners SpecificationsService Hints Technical ServiceMain Burner Cleaning and MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole LogsObserved Problem Possible Cause TroubleshootingMaintenance, Observed Problem Possible Cause RemedyTop Equipment Shutoff Valve GA5010 AccessoriesCleaning KIT CCK Parts CentralsSL30NT Illustrated Parts BreakdownKEY Part Description QTY Parts ListCisc Cisg Included In Hardware Kit Warranty Information

SL30NT specifications

Desa Tech SL30NT is an advanced and efficient machine designed for various industrial applications. Its robust construction and innovative technology make it a reliable choice for businesses looking to enhance their production capabilities. This model stands out due to its combination of power, precision, and versatility.

One of the main features of the SL30NT is its high-performance engine. The machine is equipped with a powerful motor that delivers exceptional torque and speed, allowing it to handle a wide range of tasks with ease. This makes it suitable for both heavy-duty applications and more intricate tasks that require a delicate touch.

Another significant characteristic of the SL30NT is its advanced control system. The machine features a user-friendly interface that allows operators to easily manage settings and monitor performance in real-time. This technological advancement not only enhances efficiency but also reduces the likelihood of errors during operation. With programmable settings and customization options, users can optimize the machine for specific processes.

The SL30NT also incorporates modern safety features, ensuring that operators can work confidently and securely. Emergency stop buttons, safety guards, and advanced sensors help to prevent accidents and protect both personnel and equipment. This emphasis on safety is crucial in industrial environments where the risk of injury is inherent.

In terms of technology, the SL30NT boasts an integrated automation system. This feature streamlines workflow by enabling the machine to perform tasks with minimal human intervention. Automation not only improves productivity but also ensures consistent quality in the output. The machine's ability to integrate with other systems and software further enhances its functionality, making it a valuable asset for any production line.

Additionally, the SL30NT is built with durability in mind. Its construction uses high-quality materials that withstand the rigors of industrial use, ensuring a long service life. Regular maintenance is facilitated by the machine’s design, allowing for easy access to components that require servicing.

In summary, the Desa Tech SL30NT is a state-of-the-art machine that excels in performance, safety, and versatility. Its advanced features and technology make it an indispensable tool for businesses aiming for operational excellence. Whether in manufacturing, assembly, or other industrial applications, the SL30NT promises reliability and efficiency, marking it as a leader in its class.
Top Page Image Contents