Desa Installing Damper Clamp Accessory for Vented Operation, Installing Heater Base Assembly

Page 10

10

INSTALLATION

Installing Damper Clamp Accessory For Vented Operation Installing Heater Base Assembly

INSTALLATION

Continued

INSTALLING DAMPER CLAMP ACCESSORY FOR VENTED OPERATION

Note: When used as a vented heater, appliance must be installed only in a solid-fuel burning fireplace with a working flue and constructed of noncombustible material.

If your heater is a manually-controlled model, you may use this heater as a vented product. There are three reasons for operating your heater in the vented mode.

1.The fireplace does not meet the clearance to combustibles re- quirements for vent-free operation.

2.State or local codes do not permit vent-free operation.

3.You prefer vented operation.

If reasons number 1 or 2 above apply to you, you must permanently open chimney flue damper. You must install the damper clamp accessory (to order, see Accessories, page 32). This will insure vented operation (see Figure 10). The damper clamp will keep damper open. Installation instructions are included with clamp accessory.

See chart below for minimum permanent flue opening you must provide. Attach damper clamp so the minimum permanent flue opening will be maintained at all times.

Chimney

Minimum Permanent

Height (ft.)

Flue Opening (sq. ins.)

 

 

6' to 15'

39 sq. inches

15' to 30'

29 sq. inches

 

 

Area of Various Standard

Round Flues

Diameter (ins.)

Area (sq. ins.)

 

 

5"

20 sq. inches

6"

29 sq. inches

7"

39 sq. inches

8"

51 sq. inches

 

 

Damper Clamp

Damper

DamperDamper

Masonry Fireplace Manufactured Fireplace

Figure 10 - Attaching Damper Clamp

INSTALLING HEATER BASE ASSEMBLY

CAUTION: Do not remove the data plates attached to the heater base assembly. The data plates contain important warranty and safety information.

WARNING: You must secure this heater to fire- place floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.

WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting and con- trols being damaged. Raise fireplace floor with non- combustible material. Make sure material is secure.

CAUTION: Do not pick up heater base assembly by the burner. This could damage heater. Only handle base assembly by grates.

IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly. For thermostat models, avoid damage to thermostat bulb. Avoid nicks or sharp bends in thermostat bulb wire. Keep thermostat bulb in mounting bracket until ready to mount base to floor. See Optional Positioning Of Thermostat Sensing Bulb, page 24.

Installation Items Needed

•hardware package (provided with heater)

•approved flexible gas hose (not provided) (if allowed by local codes)

•sealant (resistant to propane/LP gas, not provided)

•electric drill with 3/16" drill bit

•flathead screwdriver

1.Apply pipe joint sealant lightly to male threads of the fitting to be threaded into gas regulator. Connect approved flexible gas hose to gas regulator of heater (see Figure 11, page 11).

IMPORTANT: Hold gas regulator with wrench when connect- ing flexible gas hose.

2.Locate masonry screws in hardware package.

3.Position heater base assembly in fireplace.

4.Place logs in their proper position on heater base (see Install- ing Logs, pages 13 through 15).

5.Center heater base and logs front-to-front and side-to-side in fireplace.

6.Carefully remove logs without moving heater base.

For..com

107068-01F

Page 9 Page 11
Image 10
Page 9 Page 11
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualCLD3924PTA, CLD3924NTA Winchester Oak Model ShownTable of Contents Safety InformationProduct Identification Unpacking Product FeaturesLocal Codes AIR for Combustion and VentilationConfined Space and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsMinimum Fireplace Clearance to Combustible Materials Check GAS TypeMinimum Firebox Size If Not Using Mantel Minimum Noncombustible Material ClearancesFloor Clearances Determining Minimum Mantel Clearance when Using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Area of Various Standard Round FluesConnecting to GAS Supply Attaching Flexible Gas Hose to Heater Gas RegulatorPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Heater Gas Connections Equipment Shutoff ValveInstalling Front Log Operating Heater What to do if YOU Smell GASLighting Instructions Variable Control OperationShutting Off Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off Burners Only pilot stays litThermostat Control Operation Cleaning Maintenance Inspecting BurnersService Hints Technical ServiceReplacement Parts Troubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement at Optional Positioning of Thermostat Sensing Bulb For Masonry and Factory-built Metal FireplaceSpecifications Model CGS2718P CLD3018PA CLD3018PT CGS3124P CLD3924PTAIllustrated Parts Breakdown Parts List Variable Manually-Controlled Winchester Oak ModelsCLD3018NA CLD3018PA KEY Part Number CLD3018NA CLD3018PA Description QTY CLD3924NTA CLD3924PTA CLD3018PTParts List Accessories Parts CentralOwners Registration Form Postage Required 107068-01F Warranty Information

CGS2718P, CGS2718N, CGS3124P, CGS3124N, CLD3018PA, CLD3018NA, CLD3924PTA, CLD3924NTA, CLD3018PT, CLD3018NA specifications

Desa has made a significant impact in the home heating market with its range of innovative products. Among these, the models CGS2718P, CGS2718N, CGS3124P, CGS3124N, CLD3018PA, CLD3018NA, CLD3924PTA, CLD3924NTA, CLD3018PT, and CLD3018NA stand out for their advanced features, technologies, and user-friendly characteristics.

The CGS2718P and CGS2718N are known for their compact design and energy-efficient performance, making them ideal for various settings from residential spaces to smaller commercial applications. These models typically offer a high heating capacity with minimal energy consumption. Their easy-to-use controls allow for precise temperature adjustments, ensuring optimal comfort. Both versions are equipped with safety features to prevent overheating and unwanted gas leaks, highlighting Desa’s commitment to user safety.

On the other hand, the CGS3124P and CGS3124N models elevate performance with larger heating capabilities. These models incorporate modern technology that maximizes heat output while minimizing emissions, aligning with environmentally friendly practices. Their sleek designs blend well with different interior styles, while being robust enough for prolonged use. They often come with remote control features, enhancing user convenience.

Moving on to the CLD series, the CLD3018PA and CLD3018NA are designed to cater to users seeking versatility and performance. These models feature dual fuel capability, allowing for either propane or natural gas usage, providing flexibility depending on availability. Their advanced ignition systems ensure quick and reliable starting, while the stylish appearance complements any décor, making them a popular choice for homeowners.

The CLD3924PTA and CLD3924NTA extend the line with enhanced heating capabilities, giving users even more options for whole-home heating or larger spaces. These units are structured for efficient fuel utilization and come equipped with cutting-edge thermostat technology for accurate temperature regulation.

Finally, the CLD3018PT and CLD3018NA models serve as adaptable solutions that cater to various heating needs. Featuring modern aesthetics and user-friendly installations, these units provide reliable warmth and comfort.

Overall, the Desa series combines thoughtful engineering with aesthetic design, making them an appealing choice for anyone looking to enhance their home's warmth while maintaining efficiency and safety.
Top Page Image Contents