Desa CGP10L, CGP6L Attaching to wall anchor method, Placing Heater On Mounting Screws

Page 7

OWNER’S MANUAL

INSTALLING TO WALL

Continued

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are in hardware package. The hardware pack- age is provided with heater.

Attaching to wall stud method

For attaching mounting screw to wall stud

1.Drill hole at marked location using 9/64" drill bit.

2.Insert mounting screw into wall stud.

3.Tighten screw until 1/16" space (thick- ness of penny) is between screwhead and wall.

Attaching to wall anchor method

Follow instructions below to attach mount- ing screws to hollow walls (wall areas be- tween studs) or solid walls (concrete or masonry).

5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8).

Thin or Thick Wall

(thick wall

shown)

1/16" Space

Solid

Wall

ANCHOR

Figure 8 - Tightening Anchors

Placing Heater On Mounting Screws

1.Locate two keyhole slots on back panel of heater (see Figure 9).

2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 un- der Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill hole at marked lo- cation using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11).

7.Tighten screw until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 8 and 9).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.

2.Fold wall anchor (see Figure 6).

Figure 6 - Folding Anchor

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7).

IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

Thin Walls (1/4" to 1/2" thick)

Keyhole Slots

Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater

Removing Front Panel Of Heater

1.Remove two screws near bottom cor- ners of front panel.

2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".

3.Pull bottom of front panel forward, then down.

Figure 11 - Installing Bottom Mounting Screw

Figure 7 - Popping Open Anchor Wings

Figure 10 - Removing Front Panel Of

For Thin Walls

Heater

 

 

 

103547

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualUnpacking Safety InformationProduct Features Local CodesUnusually Tight Construction Product IdentificationFresh AIR for Combustion and Ventilation Providing Adequate VentilationVentilation AIR Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building Ventilation Air From Outdoors Fresh AIR for Combustion VentilationCheck GAS Type Installing to WallInstallation Items Installing Heater to WallRemoving Front Panel Of Heater Installing Bottom Mounting ScrewAttaching to wall anchor method Placing Heater On Mounting ScrewsExternal Regulator With Vent Pointing Down Connecting to GAS SupplyOperating Heater Checking GAS ConnectionsPilot Flame Pattern Manual Lighting ProcedureInspecting Burner Lighting InstructionsCabinet Cleaning and MaintenanceBurner Flame Pattern ODS/PILOT and Burner OrificeObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Service Hints Technical ServiceAccessory Parts Centrals SpecificationsReplacement Parts Service PublicationsCGP10L CGP6L Illustrated Parts ListParts Available not Shown 10,000 and 6,000 BTU/HR PROPANE/LP GAS Heater 103547 Warranty Information

CGP10L, CGP6L specifications

Desa's CGP10L and CGP6L are two innovative gas-powered heating solutions designed for both residential and commercial applications. These models highlight an impressive combination of efficiency, convenience, and modern technology tailored to meet diverse heating needs.

The CGP10L is a robust heater with a capacity of 10,000 BTUs, making it an ideal choice for larger spaces or areas requiring extensive heating. In contrast, the CGP6L offers a slightly lower output of 6,000 BTUs, perfect for smaller rooms or as supplemental heating in larger environments. Both models are designed to deliver reliable warmth while maintaining energy efficiency, which is crucial for cost-effective household management.

One of the standout features of the CGP10L and CGP6L is the use of advanced infrared technology. This technology allows for quick and efficient heating by warming objects and people directly rather than merely heating the air. As a result, users can experience immediate comfort without the typical waiting times associated with traditional heating systems.

In terms of design, both models feature a compact and lightweight construction, enabling easy portability. This is particularly beneficial for users who may want to move their heater from room to room or even take it outdoors. The built-in safety features, such as automatic shut-off functions and tip-over protection, enhance the safety profile of these units, making them suitable for various living conditions.

Moreover, Desa has incorporated user-friendly controls in both models, allowing users to adjust the heat output according to their comfort preferences. The straightforward operation ensures that even those who are not technically inclined can benefit from these powerful heating systems.

The fuel efficiency of the CGP10L and CGP6L is another attractive characteristic, as both models are designed to minimize gas consumption while maximizing heat output. This not only contributes to lower utility bills but also aligns with eco-friendly practices.

In conclusion, Desa's CGP10L and CGP6L heaters stand out in the market due to their modern technology, efficiency, portability, and safety features. Whether for residential or commercial use, these models provide a reliable heating solution tailored to meet the varying demands of consumers.
Top Page Image Contents