Desa CLD3924NT, CLD3018N Installing Logs on Models CGS2718N and CGS3124N, Installing Back Log

Page 13

OWNER’S MANUAL

INSTALLATION

Continued

INSTALLING LOGS ON MODELS CGS2718N AND CGS3124N

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to High, check to see if flames contact any log. If so, re- position logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Locate pegs on the bottom of back log (#1). Slide these pegs into the holes in the grate base behind the burner (see Figure 16).

2.Locate the notches on the back of the front log (#2). Slide these notches over the tabs of the grate base (see Figure 17).

3.Locate the notches in the bottom of the crossover log (#3). Place the crossover log on top of the back log and front log. Make sure the notches of the crossover log line up with rectangular knobs on top of the back and front logs (see Fig- ure 18).

4.Add lava rock around base of heater. Do not place lava rock on logs or burner.

Back Log (#1)

Peg

Hole

Peg

Figure 16 - Installing Back Log

Front Log (#2)

Notch

Tabs of

Grate Base

Figure 17 - Installing Front Log

Crossover
Log (#3)	Notch
Notch	Rectangular
Notch	Knob

Rectangular

Knob

Figure 18 - Installing Crossover Log

Continued

104385

13

Image 13

Contents Winchester Oak Model Shown What to do if YOU Smell GASPatent Pending Unvented Natural GAS LOG Heater Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined Space and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Ventilation AIRBuilding Ventilation Air From OutdoorsCheck GAS Type InstallationMinimum Wall and Ceiling Clearances see Figure If Not Using Mantel If Using MantelMinimum Noncombustible Material Clearances Floor Clearances Mantel ClearancesDetermining Minimum Mantel Clearance Installing Heater Base Assembly Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Chimney Minimum Permanent Height ft Flue Opening sq. insAttaching Flexible Gas Hose to Heater Gas Regulator Connecting to GAS SupplyPressure Testing Heater Gas Connections Pressure Testing gas Supply Piping systemChecking GAS Connections Test Pressures In Excess Of 1/2 PsigInstalling Back Log Installing Logs on Models CGS2718N and CGS3124NDamage or personal injury Installing Logs on Models CLD3018N and CLD3924NTFront Log #1 Grate Fingers Grate Base Installing Logs on Model CCL3930NTAOperating Heater For Your Safety Read Before LightingLighting Instructions Variable Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterThermostat Control Operation Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning and MaintenanceMain Burner ODS/PILOT and BurnerObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at TopFor Masonry and Factory- built Metal Fireplace Optional POSI- Tioning of THER- Mostat Sensing BulbTechnical Service SpecificationsService Hints Replacement PartsParts Central AccessoriesManual Shutoff Fireplace HoodIllustrated Parts Breakdown CGS2718N CGS3124N Parts ListUnvented Natural GAS LOG Heater CLD3018N CLD3924NT KEY CLD3924NT Part Number Description QTY CCL3930NTA CCL3930NT CCL3930NTA CCL3930NT CCL3930NTAWarranty Information