Desa CLD3018N Installing Logs on Model CCL3930NTA, Front Log #1 Grate Fingers Grate Base

Page 15

OWNER’S MANUAL

INSTALLATION

Continued

INSTALLING LOGS ON MODEL CCL3930NT(A)

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION:Afterinstallationand periodically thereafter, check to en- sure that no flame comes in contact with any log. With the heater set to High, check to see if flames contact any log. If so, reposition logs ac- cording to the log installation in- structions in this manual. Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place the front log (#1) on the grate fin- gers. Make sure the front log rest firmly between the grate fingers and the grate base (see Figure 23).

2.Place the base of the middle log (#2) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 24). Make sure the front of the middle log is resting on the tabs of the grate base.

3.Locate pegs on the bottom of back log (#3). Slide these pegs into the holes in the grate base behind the burner (see Figure 25).

Front Log (#1)

Grate

Fingers

Grate Base

Figure 23 - Installing Front Log (#1)

4.Locate pegs on the bottom of crossover log (#4). Slide these pegs into the holes located in middle log (#2) and back log (#3). See Figure 26 for placement.

5.Locate pegs on the bottom of crossover log (#5). Slide these pegs into the holes located in crossover log (#4) and front log (#1). See Figure 27.

Middle Log (#2)

Burner

Tab

U-Shaped

 

Slot

Figure 24 - Installing Middle Log (#2)

Pegs

Hole in

Grate Base

Burner

Figure 25 - Installing Back Log (#3)

Pegs

Log #2

Log #3

Figure 26 - Installing Crossover Log (#4)

6.Locate pegs on the bottom of crossover log (#6). Slide these pegs into the holes located in back log (#3) and front log (#1). See Figure 28.

7.Locate pegs on the bottom of crossover log (#7). Slide these pegs into the holes located in crossover log (#6) and front log (#1). See Figure 29.

8.Add lava rock around base of heater. Do not place any lava rock on logs or burner.

Crossover Log (#4)

Front Log (#1)

Figure 27 - Installing Crossover Log (#5)

Pegs

6

Log #2

Front Log (#1)

Figure 28 - Installing Crossover Log (#6)

Pegs

7

Crossover

Log (#6)

Front Log (#1)

Figure 29 - Installing Crossover Log (#7)

104385

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS Winchester Oak Model ShownPatent Pending Unvented Natural GAS LOG Heater Safety InformationUnpacking Product FeaturesProduct Identification Local CodesConfined Space and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside BuildingInstallation Check GAS TypeMinimum Wall and Ceiling Clearances see Figure If Using Mantel If Not Using MantelMinimum Noncombustible Material Clearances Mantel Clearances Floor ClearancesDetermining Minimum Mantel Clearance Chimney Minimum Permanent Height ft Flue Opening sq. ins Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Installation Items NeededAttaching Flexible Gas Hose to Heater Gas Regulator Connecting to GAS SupplyTest Pressures In Excess Of 1/2 Psig Pressure Testing gas Supply Piping systemPressure Testing Heater Gas Connections Checking GAS ConnectionsInstalling Back Log Installing Logs on Models CGS2718N and CGS3124NDamage or personal injury Installing Logs on Models CLD3018N and CLD3924NTFront Log #1 Grate Fingers Grate Base Installing Logs on Model CCL3930NTAFor Your Safety Read Before Lighting Operating HeaterLighting Instructions Shutting Off Heater Manual Lighting ProcedureVariable Control Operation To Turn OFF GAS To ApplianceBurner Primary AIR Holes Inspecting BurnersThermostat Control Operation Pilot Flame PatternODS/PILOT and Burner Cleaning and MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Main BurnerObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at TopFor Masonry and Factory- built Metal Fireplace Optional POSI- Tioning of THER- Mostat Sensing BulbReplacement Parts SpecificationsTechnical Service Service HintsFireplace Hood AccessoriesParts Central Manual ShutoffIllustrated Parts Breakdown CGS2718N CGS3124N Parts ListUnvented Natural GAS LOG Heater CLD3018N CLD3924NT KEY CLD3924NT Part Number Description QTY CCL3930NTA CCL3930NT CCL3930NTA CCL3930NT CCL3930NTAWarranty Information
Top Page Image Contents