Desa CGB3924NR, CGB3930NR Product Identification, Product Features, Local Codes, Unpacking

Page 3

OWNER’S MANUAL

PRODUCT

IDENTIFICATION

Back Log

Crossover Log

Front Log

Remote

Burner

Control

 

Middle Log Piezo Ignitor

Remote Selector Switch

PRODUCT

FEATURES

Operation

This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney. Heat is generated by realistic dancing, yellow flames. This heater is designed for vent-free operation with flue damper closed. State and local codes in some areas prohibit the use of vent-free heaters.

Safety Pilot

This heater has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS). The ODS/pilot is a required feature for vent- free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.

Piezo Ignition System

Flame Adjustment Knob

Base Grate

This heater has a piezo ignitor. This system

Control Knob

Figure 1 - Yellow Flame Vent-Free Gas Log Heater Shown (Logs May Vary by Model)

requires no matches, batteries, or other sources to light heater.

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code ANSI Z223, also known as NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

1.Remove logs and heater base assem- bly from carton. Note: Do not pick up heater base assembly by burners. This could damage heater. Always handle base assembly by grate.

2.Remove all protective packaging ap- plied to logs and heater for shipment.

3.Check all items for any shipping dam- age. If damaged, promptly inform dealer where you bought heater.

104306

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents What to do if YOU Smell GAS Yellow Flame Model ShownSafety Information Unpacking Product FeaturesProduct Identification Local CodesConfined Space and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation LOG Sizing RequirementsIf Not Using Mantel If Using MantelMinimum Non-Combustible Material Clearances Floor Clearances Mantel ClearancesInstallation Items Needed Installing Heater Base AssemblyTest Pressures In Excess Of 1/2 Psig Connecting to GAS SupplyPressure Testing gas Supply Piping system Checking GAS ConnectionsInstalling 9-Volt Battery In Hand- Held Remote Control Unit Volt Battery InstallationPressure Testing Heater Gas Connections Installing 9-Volt Alkaline Battery In ReceiverPlace the base of the middle log #2 Installing Logs CGD3924NRInstalling Back Log #2 Installing Logs on Models CGB3924PR and CGB3930PRFor Your Safety Read Before Lighting Operating HeaterLighting Instructions Hand Held Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationInspecting Burners Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at TopService Hints SpecificationsaccessoriesWiring Diagram Technical ServiceCGD3924NR Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListCGB3924NR CGB3930NR KEY CGB3924NR CGB3930NR Part Number Description QTY Parts Central Replacement PartsParts Under Warranty Parts not Under Warranty104306 Warranty Information
Top Page Image Contents