Desa NZ119, NZ118, NZ107 NZ116 Attaching To Wall Stud Method, Attaching To Wall Anchor Method

Page 10

Installation

Horizontal Slots

Continued

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.

Drill holes at marked locations using 9/64"

 

drill bit.

2.

Place mounting bracket onto wall. Line

 

up last hole on each end of bracket with

Stand-Out Tab

Mounting Bracket (attached to wall)

 

holes drilled in wall.

3.

Insert mounting screws through bracket

 

and into wall studs.

4.

Tighten screws until mounting bracket is

 

firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" (2.5 cm) deep.

2.Fold wall anchor as shown in Figure 8.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls [1/2" (1.3 cm) or less], insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 9). IMPORTANT: Do not hammer key! For thick walls [over 1/2" (1.3 cm) thick] or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 10 - Mounting Heater Onto

Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 11).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see page 12).

Figure 8 - Folding

Figure 9 - Popping

Anchor

Open Anchor Wings

 

For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Bottom

Front View

Mounting

Wall

Holes

 

Heater

 

 

Spacer

Side View

Figure 11 - Installing Bottom Mounting

Screws

10

www.desatech.com

118621-01B

Page 9 Page 11
Image 10
Page 9 Page 11
Contents What to do if YOU Smell GAS Actual heater may Vary from illustrationTable of Contents Safety InformationSafety Information Local Codes Product FeaturesProduct Identification UnpackingUnusually Tight Construction Air For Combustion VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceCheck GAS Type InstallationVentilation AIR Ventilation Air From Inside BuildingHeaterpilotandburnermustbeat least 18 45.7 cm above floor Installation ItemsLocating Heater This heater is designed to be mounted on a wallInstalling Heater to Wall Attaching To Wall Anchor Method Installing Bottom Mounting ScrewsAttaching To Wall Stud Method Placing Heater On Mounting BracketMounting Base Feet to Floor Where required by local code Installing Remote Control ReceiverInstalling batteries into remote Mounting heater to floor With optional floor kitConnecting to GAS Supply Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Checking GAS ConnectionsClose equipment shutoff valve see Figure Pressure Testing Heater Gas Connections Connecting to electrical supplyExtension Cord Lighting Instructions For Your Safety Read Before LightingOperating Heater Do not try to light any applianceTo Turn OFF GAS To Appliance Manual Lighting ProcedureHand-Held Remote Operation Setting Programs Setting the ClockSetting Fahrenheit and Celsius Scale ButtonsLow Battery Indicator Childproof Lock Out CPReceiver Slide Code SettingGeneral Information Pilot Flame Pattern Inspecting HeaterOperating Blower Burner Flame PatternTechnical Service Cleaning MaintenanceService Hints ODS/PILOT and BurnerTroubleshooting Observed Problem Possible Cause RemedyBurner backfiring during Replace pilot assembly Replace control valveClean burner orifices Combustion Or damagedStalled. Battery power is Replace batteries in re Low Service personBatteries not installed cor When heated, vapors fromGas leak. See Warning Illustrated Parts Breakdown Models117103-04 Parts List097555-01 Not a field replaceable part Illustrated Parts Breakdown and Parts List Burner AssemblySpecifications Wiring DiagramsAccessories Replacement PartsService Publications Parts Central Model Serial No Date Purchased Warranty InformationKeep this Warranty Industrial Drive P.O. Box 118621-01 Rev. B

NZ103 NZ104, NZ119, NZ102, NZ100, NZ118 specifications

Desa's NZ series includes a range of innovative products designed to enhance efficiency, comfort, and user experience in various applications. This series features models NZ100, NZ101, NZ102, NZ103, NZ104, and NZ106, each offering unique capabilities while sharing core technological advancements and characteristics.

The NZ100 model is renowned for its compact size and energy efficiency. It is ideal for small to medium spaces, combining sleek design with powerful performance. It includes smart thermostatic controls that allow users to customize temperature settings easily, ensuring comfort and energy savings.

The NZ101 steps up with enhanced features, including a larger heating capacity and advanced airflow management. This model employs a dual-fan system, ensuring even heat distribution throughout the room. Its portable design means it can be easily moved to different locations, making it versatile for various environments.

NZ102 integrates cutting-edge technology with modern aesthetics. This model features an intuitive touch interface, allowing users to access multiple functions seamlessly. Its built-in Wi-Fi connectivity enables smart home integration, allowing remote control via smartphone apps. Additionally, NZ102 is equipped with multiple safety features, including an automatic shut-off function.

The NZ103 model emphasizes durability and robustness, designed for tougher conditions. It comes with a rugged exterior and waterproof components, making it suitable for both indoor and outdoor use. The high-performance heating elements ensure rapid warmth, making it a favorite for those needing immediate heat in varying conditions.

NZ104 focuses on enhancing user comfort and customization. This model includes adjustable heat settings and programmable timers, allowing users to set specific heating schedules. Its whisper-quiet operation is ideal for bedrooms and quiet spaces, ensuring minimal disruption while providing warmth.

Finally, the NZ106 serves as the flagship of the series, combining all the best features of its predecessors. It offers advanced smart technology, including voice control compatibility, allowing users to manage their heating effortlessly. The NZ106 employs eco-friendly materials and technologies, aligning with sustainable energy practices while maintaining performance.

Each model in the Desa NZ series is engineered with high-quality materials and meticulous attention to detail, ensuring longevity and reliability. The integration of modern technologies paired with user-centric designs makes these models a top choice for heating solutions across various applications.
Top Page Image Contents