Desa NZ103 NZ104, NZ119, NZ118 Buttons, Setting the Clock, Setting Fahrenheit and Celsius Scale

Page 17

Operating Heater

 

Continued

 

 

2

 

 

 

P1

AM

P2

ON

3

P1

P2

OFF

 

PM

 

THERMO

 

 

 

 

8

 

 

 

 

7

 

 

 

4

1

ROOM

 

SET

 

 

PM

 

 

5

 

 

 

FLAME

 

 

6

 

 

 

Figure 25 - LCD Display

Buttons

MODE - Changes modes from ON, THERMO and OFF.

DOWN - Lowers set temperature in THERMO mode.

UP - Increases set temperature in THERMO mode

TIME/PROGRAM - Activates time setting and activates PROGRAM mode.

SET - Used to set clock and timer.

Mode

Button

DOWN UP

TIME/PROGRAM SET

Figure 26 - Mode Buttons

Setting the Clock

Slide open plastic cover on front of remote control to expose setting buttons.

The cover protects buttons from being changed accidentally. Close cover after completing the following settings and programming.

1.Press and hold TIME/PROGRAM button on remote control for more than 2 sec- onds. Hour digit(s) will begin flashing.

2.Press UP or DOWN button until desired hour is displayed in AM or PM.

3.Press and release TIME/PROGRAM button again and minute digits will begin flashing.

4.Press UP or DOWN button until desired minutes are displayed.

5.Press and release SET button on remote control to stop time digits from flashing and set the time.

Note: Flashing numbers on display indicate system is awaiting user input, such as using UP and DOWN buttons to program a new setting. If no change is made to flashing dig- its within 15 seconds, system will complete procedure last programmed and reset the display to its normal state.

Setting Fahrenheit and Celsius Scale

Factory setting for temperature is 0° F. To change this setting to 0° C, press UP but- ton and DOWN button on remote control at the same time to change from 0° F to 0° C. Follow this same procedure to change from 0° C back to 0° F.

Manual Function

To operate system in ON manual mode, press MODE button. The flame icon will come on. The word ON and the flame icon will appear on LCD screen in ON mode.

To operate system in OFF manual mode, press MODE button again. The FLAME icon will shut off. The word OFF will appear on LCD screen. The flame icon will not appear on LCD screen in OFF mode.

Thermostat Function

This remote control system can be thermo- statically controlled when remote control is in THERMO mode (THERMO must be dis- played on the screen). To set desired room temperature, press MODE button to place re- mote control into THERMO mode, then press UP or DOWN button to select desired room temperature. Within 5 seconds appliance will turn on or off. The highest SET temperature is 99° F (37° C). The lowest SET temperature is 45° F (8° C). The factory set number will be 45° F (8° C).

If room temperature is higher than 99° F, the word HI will display on the room temperature window frame. If room temperature is lower than 32° F, the word LO will display on the room temperature window frame.

Operational Note: To conserve battery power, changes in room temperature are automatically updated every 2 minutes to remote control. Mode button will operate on-thermo-off in series that will cycle from ON to THERMO to OFF.

Setting Programs

In Program Mode, remote control will allow heater to automatically turn on and off at spe- cific times. Two on and off segments per day may be set, or settings previously programmed at the factory may be used. On and off times are available in 15 minute increments.

118621-01B

www.desatech.com

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Actual heater may Vary from illustration What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Product Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation Air For Combustion VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation AIR InstallationCheck GAS Type Ventilation Air From Inside BuildingLocating Heater Installation ItemsHeaterpilotandburnermustbeat least 18 45.7 cm above floor This heater is designed to be mounted on a wallInstalling Heater to Wall Attaching To Wall Stud Method Installing Bottom Mounting ScrewsAttaching To Wall Anchor Method Placing Heater On Mounting BracketInstalling batteries into remote Installing Remote Control ReceiverMounting Base Feet to Floor Where required by local code Mounting heater to floor With optional floor kitConnecting to GAS Supply Close equipment shutoff valve see Figure Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Extension Cord Connecting to electrical supplyPressure Testing Heater Gas Connections Operating Heater For Your Safety Read Before LightingLighting Instructions Do not try to light any applianceHand-Held Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Setting Fahrenheit and Celsius Scale Setting the ClockSetting Programs ButtonsChildproof Lock Out CP Low Battery IndicatorGeneral Information Code SettingReceiver Slide Operating Blower Inspecting HeaterPilot Flame Pattern Burner Flame PatternService Hints Cleaning MaintenanceTechnical Service ODS/PILOT and BurnerObserved Problem Possible Cause Remedy TroubleshootingClean burner orifices Replace pilot assembly Replace control valveBurner backfiring during Combustion Or damagedBatteries not installed cor Service personStalled. Battery power is Replace batteries in re Low When heated, vapors fromGas leak. See Warning Models Illustrated Parts Breakdown097555-01 Not a field replaceable part Parts List117103-04 Burner Assembly Illustrated Parts Breakdown and Parts ListWiring Diagrams SpecificationsService Publications Replacement PartsAccessories Parts Central Keep this Warranty Warranty InformationModel Serial No Date Purchased Industrial Drive P.O. Box 118621-01 Rev. B

NZ103 NZ104, NZ119, NZ102, NZ100, NZ118 specifications

Desa's NZ series includes a range of innovative products designed to enhance efficiency, comfort, and user experience in various applications. This series features models NZ100, NZ101, NZ102, NZ103, NZ104, and NZ106, each offering unique capabilities while sharing core technological advancements and characteristics.

The NZ100 model is renowned for its compact size and energy efficiency. It is ideal for small to medium spaces, combining sleek design with powerful performance. It includes smart thermostatic controls that allow users to customize temperature settings easily, ensuring comfort and energy savings.

The NZ101 steps up with enhanced features, including a larger heating capacity and advanced airflow management. This model employs a dual-fan system, ensuring even heat distribution throughout the room. Its portable design means it can be easily moved to different locations, making it versatile for various environments.

NZ102 integrates cutting-edge technology with modern aesthetics. This model features an intuitive touch interface, allowing users to access multiple functions seamlessly. Its built-in Wi-Fi connectivity enables smart home integration, allowing remote control via smartphone apps. Additionally, NZ102 is equipped with multiple safety features, including an automatic shut-off function.

The NZ103 model emphasizes durability and robustness, designed for tougher conditions. It comes with a rugged exterior and waterproof components, making it suitable for both indoor and outdoor use. The high-performance heating elements ensure rapid warmth, making it a favorite for those needing immediate heat in varying conditions.

NZ104 focuses on enhancing user comfort and customization. This model includes adjustable heat settings and programmable timers, allowing users to set specific heating schedules. Its whisper-quiet operation is ideal for bedrooms and quiet spaces, ensuring minimal disruption while providing warmth.

Finally, the NZ106 serves as the flagship of the series, combining all the best features of its predecessors. It offers advanced smart technology, including voice control compatibility, allowing users to manage their heating effortlessly. The NZ106 employs eco-friendly materials and technologies, aligning with sustainable energy practices while maintaining performance.

Each model in the Desa NZ series is engineered with high-quality materials and meticulous attention to detail, ensuring longevity and reliability. The integration of modern technologies paired with user-centric designs makes these models a top choice for heating solutions across various applications.
Top Page Image Contents