Desa NZ118 Mounting heater to floor With optional floor kit, Installing Remote Control Receiver

Page 11

Installation

Continued

Mounting heater to floor With optional floor kit

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 12).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Wood

Screw

2.Remove battery cover on receiver and install batteries as shown in Figure 13. Replace battery cover.

3.Remove adhesive backing on hook and loop strip and attach to receiver in location shown in Figure 14.

4.Place receiver with hook and loop strip’s sticky side down in approximate location on inside of heater shown in Figure 14.

5.Connect wires from receiver to wires on control valve solenoid.

Receiver

OFF

REMOTE

AA Batteries

Battery Cover

Figure 13 - Installing Batteries in

Receiver

Base Foot

Sheet Metal Screw

Figure 12 - Installing Base Feet (actual

heater may vary from illustration)

Mounting Base Feet to Floor (Where required by local code)

1.Remove front panel (see Removing Front Panel of Heater, page 9).

2.Position heater with base feet in desired location. Mark holes for drilling. Remove heater with base.

3.For carpeted floors, make a small cut with a sharp knife at marked locations prior to drilling. If mounting base to a wood floor, drill 1/8" diameter hole, 3/4" deep. (Do not use anchors in wood floors).

If mounting base to a concrete floor, drill with 1/4" diameter concrete drill bit, 13/8" into floor. Insert anchors completely into holes.

4.Reposition heater with base feet over holes. Secure base to floor with wood screws. See Figure 12.

installing Remote Control Receiver

Remote control receiver must be installed to operate the remote control.

1.Locate two packages of AA batteries, remote receiver and hook and loop strip in hardware bag included with your heater.

Receiver

 

Burner

 

 

Hook and

REMOTE

Heater

Cabinet

Loop Strip

OFF

 

on Bottom

 

 

of Receiver

 

 

Figure 14 - Installing Remote Receiver

Installing batteries into remote

1.Locate hand-held remote control in hard- ware bag included with your heater.

2.Remove battery cover and insert supplied batteries into remote control as shown in Figure 15.

3.Replace battery cover.

AAA

Batteries

M

O

A

 

 

K

 

C

 

 

I

G

E

15

 

 

 

13

1

 

 

11

 

3

 

 

9

7

5

Battery Cover

Remote Control

Figure 15 - Installing Batteries in Hand-

Held Remote Control

118621-01B

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Actual heater may Vary from illustration What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Unpacking Product FeaturesProduct Identification Local CodesConfined and Unconfined Space Air For Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building InstallationVentilation AIR Check GAS TypeThis heater is designed to be mounted on a wall Installation ItemsLocating Heater Heaterpilotandburnermustbeat least 18 45.7 cm above floorInstalling Heater to Wall Placing Heater On Mounting Bracket Installing Bottom Mounting ScrewsAttaching To Wall Stud Method Attaching To Wall Anchor MethodMounting heater to floor With optional floor kit Installing Remote Control ReceiverInstalling batteries into remote Mounting Base Feet to Floor Where required by local codeConnecting to GAS Supply Close equipment shutoff valve see Figure Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Extension Cord Connecting to electrical supplyPressure Testing Heater Gas Connections Do not try to light any appliance For Your Safety Read Before LightingOperating Heater Lighting InstructionsHand-Held Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Buttons Setting the ClockSetting Fahrenheit and Celsius Scale Setting ProgramsChildproof Lock Out CP Low Battery IndicatorGeneral Information Code SettingReceiver Slide Burner Flame Pattern Inspecting HeaterOperating Blower Pilot Flame PatternODS/PILOT and Burner Cleaning MaintenanceService Hints Technical ServiceObserved Problem Possible Cause Remedy TroubleshootingCombustion Or damaged Replace pilot assembly Replace control valveClean burner orifices Burner backfiring duringWhen heated, vapors from Service personBatteries not installed cor Stalled. Battery power is Replace batteries in re LowGas leak. See Warning Models Illustrated Parts Breakdown097555-01 Not a field replaceable part Parts List117103-04 Burner Assembly Illustrated Parts Breakdown and Parts ListWiring Diagrams SpecificationsService Publications Replacement PartsAccessories Parts Central Industrial Drive P.O. Box 118621-01 Rev. B Warranty InformationKeep this Warranty Model Serial No Date Purchased

NZ103 NZ104, NZ119, NZ102, NZ100, NZ118 specifications

Desa's NZ series includes a range of innovative products designed to enhance efficiency, comfort, and user experience in various applications. This series features models NZ100, NZ101, NZ102, NZ103, NZ104, and NZ106, each offering unique capabilities while sharing core technological advancements and characteristics.

The NZ100 model is renowned for its compact size and energy efficiency. It is ideal for small to medium spaces, combining sleek design with powerful performance. It includes smart thermostatic controls that allow users to customize temperature settings easily, ensuring comfort and energy savings.

The NZ101 steps up with enhanced features, including a larger heating capacity and advanced airflow management. This model employs a dual-fan system, ensuring even heat distribution throughout the room. Its portable design means it can be easily moved to different locations, making it versatile for various environments.

NZ102 integrates cutting-edge technology with modern aesthetics. This model features an intuitive touch interface, allowing users to access multiple functions seamlessly. Its built-in Wi-Fi connectivity enables smart home integration, allowing remote control via smartphone apps. Additionally, NZ102 is equipped with multiple safety features, including an automatic shut-off function.

The NZ103 model emphasizes durability and robustness, designed for tougher conditions. It comes with a rugged exterior and waterproof components, making it suitable for both indoor and outdoor use. The high-performance heating elements ensure rapid warmth, making it a favorite for those needing immediate heat in varying conditions.

NZ104 focuses on enhancing user comfort and customization. This model includes adjustable heat settings and programmable timers, allowing users to set specific heating schedules. Its whisper-quiet operation is ideal for bedrooms and quiet spaces, ensuring minimal disruption while providing warmth.

Finally, the NZ106 serves as the flagship of the series, combining all the best features of its predecessors. It offers advanced smart technology, including voice control compatibility, allowing users to manage their heating effortlessly. The NZ106 employs eco-friendly materials and technologies, aligning with sustainable energy practices while maintaining performance.

Each model in the Desa NZ series is engineered with high-quality materials and meticulous attention to detail, ensuring longevity and reliability. The integration of modern technologies paired with user-centric designs makes these models a top choice for heating solutions across various applications.
Top Page Image Contents