Desa NZ106, NZ119, NZ118, NZ107 NZ116, NZ100, NZ105, NZ102, NZ101, NZ103 NZ104 Installing Heater to Wall

Page 9

Installation

Continued

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Re- move mounting bracket from heater carton.

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mount- ing bracket is level.

Figure 5 - Mounting Bracket

Removing Front Panel Of Heater

1.Remove the four painted screws, two on each side of front panel.

2.Pull bottom of front panel forward, then out.

3.Remove any remaining packaging ma- terials.

Front Panel

Screw

Figure 6 - Removing Front Panel Of

Heater

Methods For Attaching Mounting Bracket

To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 14" (35.6 cm) apart from their cen- ters. Attach mounting bracket to wall in one of two ways:

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

WARNING: Maintain mini- mumclearancesshowninFigure

7.If you can, provide greater clearances from floor and join- ing wall.

2.Mark screw locations on wall (see Figure 7).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

 

12"

14" (35.6 cm)

 

 

(30.4

 

 

 

cm)

 

 

AdjoiningWall

Min.

 

 

Only Insert Mounting

18 3/4"

Screws Through Last

(47.6 cm)

 

 

Hole On Each End

Min.

 

 

 

Floor

3 Plaque Heater

16"

14" (35.6 cm)

(40.6 cm)

 

Min.

 

AdjoiningWall

Only Insert Mounting

18 3/4"

Screws Through Last

(47.6 cm)

 

Hole On Each End

Min.

Floor

5 Plaque Heater

Figure 7 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall Note: Wall anchors, mounting screws and spacers are in hardware package. The hard- ware package is provided with heater.

118621-01Bwww.desatech.com

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Actual heater may Vary from illustration What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Product Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation Air For Combustion VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation AIR InstallationCheck GAS Type Ventilation Air From Inside BuildingLocating Heater Installation ItemsHeaterpilotandburnermustbeat least 18 45.7 cm above floor This heater is designed to be mounted on a wallInstalling Heater to Wall Attaching To Wall Stud Method Installing Bottom Mounting ScrewsAttaching To Wall Anchor Method Placing Heater On Mounting BracketInstalling batteries into remote Installing Remote Control ReceiverMounting Base Feet to Floor Where required by local code Mounting heater to floor With optional floor kitConnecting to GAS Supply Checking GAS Connections Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaClose equipment shutoff valve see Figure Connecting to electrical supply Pressure Testing Heater Gas ConnectionsExtension Cord Operating Heater For Your Safety Read Before LightingLighting Instructions Do not try to light any applianceManual Lighting Procedure To Turn OFF GAS To ApplianceHand-Held Remote Operation Setting Fahrenheit and Celsius Scale Setting the ClockSetting Programs ButtonsChildproof Lock Out CP Low Battery IndicatorCode Setting Receiver SlideGeneral Information Operating Blower Inspecting HeaterPilot Flame Pattern Burner Flame PatternService Hints Cleaning MaintenanceTechnical Service ODS/PILOT and BurnerObserved Problem Possible Cause Remedy TroubleshootingClean burner orifices Replace pilot assembly Replace control valveBurner backfiring during Combustion Or damagedBatteries not installed cor Service personStalled. Battery power is Replace batteries in re Low When heated, vapors fromGas leak. See Warning Models Illustrated Parts BreakdownParts List 117103-04097555-01 Not a field replaceable part Burner Assembly Illustrated Parts Breakdown and Parts ListWiring Diagrams SpecificationsReplacement Parts AccessoriesService Publications Parts Central Keep this Warranty Warranty InformationModel Serial No Date Purchased Industrial Drive P.O. Box 118621-01 Rev. B

NZ103 NZ104, NZ119, NZ102, NZ100, NZ118 specifications

Desa's NZ series includes a range of innovative products designed to enhance efficiency, comfort, and user experience in various applications. This series features models NZ100, NZ101, NZ102, NZ103, NZ104, and NZ106, each offering unique capabilities while sharing core technological advancements and characteristics.

The NZ100 model is renowned for its compact size and energy efficiency. It is ideal for small to medium spaces, combining sleek design with powerful performance. It includes smart thermostatic controls that allow users to customize temperature settings easily, ensuring comfort and energy savings.

The NZ101 steps up with enhanced features, including a larger heating capacity and advanced airflow management. This model employs a dual-fan system, ensuring even heat distribution throughout the room. Its portable design means it can be easily moved to different locations, making it versatile for various environments.

NZ102 integrates cutting-edge technology with modern aesthetics. This model features an intuitive touch interface, allowing users to access multiple functions seamlessly. Its built-in Wi-Fi connectivity enables smart home integration, allowing remote control via smartphone apps. Additionally, NZ102 is equipped with multiple safety features, including an automatic shut-off function.

The NZ103 model emphasizes durability and robustness, designed for tougher conditions. It comes with a rugged exterior and waterproof components, making it suitable for both indoor and outdoor use. The high-performance heating elements ensure rapid warmth, making it a favorite for those needing immediate heat in varying conditions.

NZ104 focuses on enhancing user comfort and customization. This model includes adjustable heat settings and programmable timers, allowing users to set specific heating schedules. Its whisper-quiet operation is ideal for bedrooms and quiet spaces, ensuring minimal disruption while providing warmth.

Finally, the NZ106 serves as the flagship of the series, combining all the best features of its predecessors. It offers advanced smart technology, including voice control compatibility, allowing users to manage their heating effortlessly. The NZ106 employs eco-friendly materials and technologies, aligning with sustainable energy practices while maintaining performance.

Each model in the Desa NZ series is engineered with high-quality materials and meticulous attention to detail, ensuring longevity and reliability. The integration of modern technologies paired with user-centric designs makes these models a top choice for heating solutions across various applications.
Top Page Image Contents