Desa RN30BT installation manual TROUBLE- Shooting, Cleaning and Mainte

Page 21

TROUBLE- SHOOTING

Continued

 

OBSERVED

POSSIBLE

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

CAUSE

 

 

 

 

REMEDY

 

 

 

 

 

 

 

 

 

 

 

 

 

When ignitor button is

1.

Gas supply turned off or

1.

Turn on gas supply or

 

 

pressed, there is spark

 

manual

shutoff

valve

 

open

manual shutoff

 

 

at ODS/pilot but no ig-

 

closed

 

 

 

 

 

valve.

 

 

 

 

 

 

nition.

2.

Control knob not in PI-

2.

Turn control knob to PI-

 

 

 

 

LOT position

 

 

 

 

LOT position.

 

 

 

 

 

 

3.

Control

knob

not

3.

Press

in control

knob

 

 

 

 

pressed in while in PI-

 

while in PILOT posi-

 

 

 

 

LOT position

 

 

 

 

tion.

 

 

 

 

 

 

 

4.

Air in gas lines when in-

 

 

 

 

 

 

 

 

 

 

stalled

 

 

 

 

4.

Continue holding down

 

 

 

 

 

 

 

 

 

 

control knob. Repeat ig-

 

 

 

 

 

 

 

 

 

 

niting operation until air

 

 

 

5.

ODS/pilot is clogged.

 

 

is removed.

 

 

 

 

 

 

 

 

 

 

 

 

5.

Clean

ODS/pilot

(see

 

 

 

 

 

 

 

 

 

 

Cleaning and Mainte-

 

 

 

 

 

 

 

 

 

 

nance, page 20) or re-

 

 

 

 

 

 

 

 

 

 

place ODS/pilot assem-

 

 

 

6.

Gas regulator setting is

 

bly.

 

 

 

 

 

 

 

 

not correct.

 

 

 

 

 

 

 

 

 

 

 

ODS/pilot lights but

1.

Control knob not fully

6.

Replace gas regulator.

 

 

 

 

 

 

 

 

 

 

 

flame goes out when

 

pressed in

 

 

 

 

 

 

 

 

 

 

 

control knob is

2.

Control

knob

not

1.

Press

in control

knob

 

 

released.

 

pressed in long enough

 

fully.

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

After

ODS/pilot lights,

 

 

 

3.

Safety interlock system

 

keep

control

knob

 

 

 

 

has been triggered (ther-

 

pressed in 30 seconds.

 

 

 

 

mostat model only).

 

3.

Wait

one minute for

 

 

 

4.

Manual

shutoff

valve

 

safety interlock system

 

 

 

 

not fully open

 

 

 

 

to reset. Repeat ignition.

 

 

 

5.

Thermocouple

connec-

4.

Fully open manual shut-

 

 

 

 

tion loose at

control

 

off valve.

 

 

 

 

 

 

 

valve

 

 

 

 

5.

Hand tighten until snug,

 

 

 

 

 

 

 

 

 

 

then tighten 1/4

turn

 

 

 

6.

Pilot flame not touching

 

more.

 

 

 

 

 

 

 

 

thermocouple, which al-

6.

A) Contact local natural

 

 

 

 

lows thermocouple

to

 

gas company.

 

 

 

 

 

 

 

cool, causing pilot flame

 

 

 

 

 

 

 

 

 

 

to go out. This problem

 

B) Clean ODS/pilot (see

 

 

 

 

could be caused by one

 

Cleaning and Mainte-

 

 

 

 

or both of the following:

 

nance, page 20) or re-

 

 

 

 

A) Low gas pressure

 

 

place ODS/pilot assem-

 

 

 

 

B) Dirty or partially

 

bly.

 

 

 

 

 

 

 

 

clogged ODS/pilot

 

 

 

 

 

 

 

 

 

 

7.

Thermocouple damaged

 

 

 

 

 

 

 

 

Burner does not light

8.

Control valve damaged

7.

Replace thermocouple.

 

 

 

 

 

 

 

 

 

 

after ODS/pilot is lit.

1.

Burner

orifice

is

8.

Replace control valve.

 

 

 

 

clogged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Clean burner (see Clean-

 

 

 

 

 

Continued

 

 

Continued

 

 

 

 

 

 

ing and Maintenance,

 

 

 

 

 

 

 

 

 

 

page

 

 

 

 

 

 

 

 

 

 

 

 

 

20) or replace

 

 

 

 

 

 

 

 

 

 

burner orifice.

 

21

 

Image 21
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualContents Safety Information Safety Information Safety Device Local Codes Unpacking Product FeaturesPiezo Ignition System Thermostatic Heat Control Thermostat Model OnlyInstallation Items Check GAS TypeLocating Heater Thermostat Sensing Bulb Locating Thermostat Sensing BulbAttaching Thermostat Sensing Bulb Mounting Bracket Installing Heater to WallRemoving Front Panel Of Heater Methods For Attaching Mounting Bracket To WallAttaching Mounting Bracket To Wall Marking Screw LocationsPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsConnecting to GAS Supply Pressure Testing GAS Supply Piping System ConnectingTo GAS Supply Checking GAS ConnectionsManual Shutoff Valve Pressure Testing Heater GAS ConnectionsFor Your Safety Read Before Lighting Operating HeaterLighting Instructions Pilot Manual Lighting Procedure To Turn OFF GAS to ApplianceThermostat Control Operation Non-Thermostat Models GRH/OV 007G Pilot Flame Pattern Inspecting BurnerBurner Flame Pattern Correct Flame Pattern AT High PositionIncorrect Flame Pattern AT High Position Observed Possible Problem Cause Remedy Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner CabinetTROUBLE- Shooting Cleaning and MainteFrom Observed Possible Problem Cause Ing statement atTop Service Hints Replacement Parts Technical ServiceParts Under Warranty Parts Not Under WarrantyFAN KIT GA2100A Parts Centrals AccessoriesManual Shutoff Floor Mounting Stand GA4000Parts IllustratedBreakdown ODS/PilotKEY Part Number Description QTY RN30B Parts ListRN30BT RN30BT Parts List Illustrated CGN18B Parts List Warranty Information Limited Warranty VENT-FREE HeatersInternational

RN30BT specifications

The Desa RN30BT is a highly regarded heating solution known for its efficiency, versatility, and contemporary design. As a compact and stylish unit, it fits seamlessly into any modern living space while providing optimal warmth and comfort. The RN30BT is not just a heater; it’s an advanced appliance equipped with a range of features designed to enhance the user experience.

At the core of the Desa RN30BT is its innovative heating technology. It utilizes advanced infrared heating which warms objects and individuals in the room rather than merely heating the air. This makes it more energy-efficient, allowing users to enjoy a comfortable environment without excessive energy consumption. The infrared heating technology also ensures that the warmth is felt almost instantaneously, a feature that is particularly appreciated during cold months.

The RN30BT comes with a user-friendly digital control panel. This feature allows users to set and monitor the desired temperature with ease. Additionally, the integrated timer function provides the flexibility to schedule heating periods, enabling users to pre-warm their spaces before returning home. This enhances convenience while also promoting energy savings.

One of the standout characteristics of the Desa RN30BT is its portability. It is designed with lightweight materials and features durable wheels, making it easy to move from one room to another. This flexibility allows users to heat different areas of their homes as needed, catering to specific heating requirements throughout the day.

Safety is paramount in the design of the RN30BT. The heater includes a range of safety features such as overheat protection and a tip-over switch that automatically shuts off the unit if it is knocked over, providing peace of mind for households with children or pets.

In terms of aesthetics, the Desa RN30BT sports a sleek and modern design that complements various interior styles. Its contemporary appearance means that it can blend in seamlessly with home décor while providing effective heating performance.

Overall, the Desa RN30BT stands out as a highly functional and stylish heating solution. With its efficient infrared technology, user-friendly controls, portability, and robust safety features, it is an ideal choice for those seeking a reliable and effective way to keep their living spaces warm and inviting throughout the colder seasons.