Desa Comprehensive Guide to Operating and Maintaining Gas Logs for Electric Heaters
Page 16

16

OPERATING HEATER

Lighting Instructions (Cont.)

To Turn Off Gas To Appliance

Manual Lighting Procedure

Hand-Held Remote Operation

OPERATING HEATER

Continued

8.With control knob pressed in, press and release ignitor but- ton. This will light pilot. The pilot is attached to the rear of the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

9.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs. Note: If pilot goes out, repeat steps 4 through 8.

10.Slightly push in and turn control knob counterclockwise to the ON position.

11.Press the on/off key on the remote control to turn on appli- ance main burner. Wait at least 5 seconds before setting desired flame height.

12.Press the up or down key until the small triangle is to the left of large flame icon at the top of LCD display (see Figure 29). Press the left or right key to set the desired flame height.

13.Replace control cover log (see Figure 26, page 15).

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

Note: The pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 7 under Lighting Instructions, page 15.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11 under Lighting Instructions in column 1.

HAND-HELD

REMOTE OPERATION

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions, page 15.

When the appliance and the remote control are switched off, the house icon with the room temperature will be displayed. When the remote control is turned on, other icons will be visible and the main burner of the appliance will turn on.

1.Turn control knob clockwise to the ON position (see Figure 25, page 15).

2.Press the ON button on remote control (see Figure 29). Wait 5 seconds to send a command to appliance.

Note: An acoustic signal will be heard that confirms the recep- tion of the command sent from the remote control.

Pilot Burner

Ignitor

Pilot Burner

Ignitor

Electrode

 

Electrode

 

 

Figure 27 - Pilot (Propane/LP) Figure 28 - Pilot (Natural)

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Press on/off key on remote control and turn control knob

clockwise to the OFF position (see Figure 25, page 15).

Shutting Off Burners Only (pilot stays lit)

Press the on/off key on remote control or turn control knob

clockwise to the PILOT position.

Small Triangle

Icon (Function

Indicator)

Flame Height

Indicator

Thermometer

Icon

Clock Icon

Left and Right

Keys Increase

and Decrease

Set Points

On/Off Button

LCD Display

Room

Temperature

Display

Sleep Timer

Display

Lock-Out

Indicator

Low Battery

Indicator

Up and Down

Keys Select

Available

Functions

Figure 29 - Remote Control

For..com

111515-01A

Page 15 Page 17
Image 16
Page 15 Page 17
Contents OWNER’S Operation Installation Manual What to do if YOU Smell GASTable of Contents Safety InformationLocal Codes UnpackingProduct Identification Product FeaturesAIR for Combustion and Ventilation Confined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationLOG Sizing Requirements If Not Using Mantel Minimum Noncombustible Material ClearancesDetermining Minimum Mantel Clearance When Using a Hood Mantel ClearancesFloor Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Installing Heater Base AssemblyInstallation Items Needed Area of Various StandardInstalling Batteries in Receiver Installing Battery into RemoteConnecting to GAS Supply Sure regulatorPressure Testing Heater Gas Connections Pressure Testing gas Supply Piping systemChecking GAS Connections Installing Logs Rear Log Log #1 PlacementOperating Heater For Your Safety Read Before LightingLighting Instructions Manual Lighting Procedure HAND-HELD Remote OperationTo Turn OFF GAS To Appliance Shutting Off HeaterInspecting Burners Pilot Flame PatternBurner Primary AIR Holes Main BurnerCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning and MaintenanceLogs Troubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement Illustrated Parts Breakdown Models LDL3924NR, LDL3924PR LDL3930NR and LDL3930PRParts List Specifications Replacement PartsWiring Diagram Service Hints Technical ServiceOwners Registration Form Postage Required Accessories Warranty Information

LDL3924NR specifications

Desa LDL3924NR is a state-of-the-art model that embodies innovative technology and advanced features aimed at providing optimal performance in its class. This model is particularly designed for users who demand reliability and efficiency in their operations.

One of the standout features of the Desa LDL3924NR is its high-performance engine. Designed to deliver excellent power output, this engine ensures that operations are smooth and efficient, making it suitable for a variety of tasks. The power-to-weight ratio is optimized, which provides the user with enhanced control and responsiveness, ensuring that even the most demanding applications can be tackled with ease.

The design of the Desa LDL3924NR incorporates advanced materials, which not only contribute to its durability but also help in reducing maintenance requirements. This characteristic is particularly beneficial for users who prioritize longevity and reliability in their equipment. Moreover, the ergonomic design ensures that the model is user-friendly, allowing operators of varying skill levels to handle it with confidence.

In terms of technology, the Desa LDL3924NR is equipped with a sophisticated control system that monitors performance metrics in real time. This technology provides users with insights into efficiency and operational status, empowering them to make informed decisions that can enhance productivity. Additionally, the model is designed with safety features that prioritize operator well-being, minimizing risks and ensuring compliance with industry standards.

Another key characteristic of the Desa LDL3924NR is its versatility. It performs reliably across different settings, whether in industrial, agricultural, or commercial environments. This multifunctionality makes it an attractive option for a diverse range of users.

In conclusion, the Desa LDL3924NR stands out due to its powerful engine, durable construction, innovative technology, and safety features. Its versatility allows it to adapt to various applications, making it an indispensable tool for professionals seeking efficiency and reliability. With its commitment to quality and performance, the Desa LDL3924NR is poised to meet the growing demands of users across multiple sectors.
Top Page Image Contents