Napco Security Technologies GEM-P816, GEM-P9600, GEM-P1632 Key Fob Transmitters, Dealer Code

Programming the GEM-P816 & GEM-P1632

16 INTERIOR						Key Fob Transmitters
						Keyfobs can be programmed as “Arm/Disarm” devices using theON and OFF
		BYPASS	FIRE/TBL	SYS TBL	CHIME	buttons (refer to control panel installation instructions).
						Press the Abutton and for each Key Fob Transmitter, enter:
						1	The Key Fob Transmitter number (01–15).
						2	The area number to which transmitter is assigned (1 or 2); enter 0 to disable
	INTERIOR	BYPASS	FIRE/TBL	SYS TBL	CHIME	keyfob.
						3	The 6-digit RF ID # printed on the transmitter (enter all numbers and/or
	(Direct Entry)					letters, including leading “0”s, if any).
								DATA	AUX 1/AUX 2
						4	The 1-digit checksum number printed on transmitter.
								ENTRY	OPTIONS
						5	The Aux-1 Option (see key fob Aux 1 & Aux 2 options).	•(blank)	None
						6	The Aux-2 Option (see key fob Aux 1 & Aux 2 options).	9	Keypad Panic
								0	Aux K.P. Panic

					B	Instant
					C	Toggle Aux Relay
					D	Access Control
KeyFob #	Area #	6-digit RF ID #	Checksum #	Aux1 #	Aux2 #
					Press Jto save. Then go to step 1

to enter next Key Fob.

When all Key Fobs are entered, press NEXT (E) button to proceed.

Note: If the Key Fob is converted for Two Button “Emergency Use” (by cutting an internal jumper), both top or bottom buttons must be depressed to activate an alarm. In this case, the Key Fob may not be used to arm or disarm the contrl panel.

NOTE: When programming the ID Code number: “A” =G0; “B” =G1;

“C” =G2; “D” =G3; “E” =G4; “F” =G5.

Key Fob Zone Assignment

Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point 3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4 buttons) or any combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone number with description/location. To assign a key fob to a zone: program the keyfob as you would a transmitter, entering the keyfob's ID code, check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If assigning a key fob to a zone, the “ON/OFF” buttons on the key fob will no longer arm/disarm the system. The key fob is converted to a “panic only” device.

ZONE DESCRIPTIONS: GEM-R3DGTL cannot be used to enter Zone Descriptions. To enter Zone Descriptions you must use the GEM-RP1CAe2 Keypad or the Napco Quickloader Software.

17 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

Dealer Code

Press the A button directly enter the Dealer Code (default = 456789), including leading zeros. Use the 1 through 9 buttons. NOTE: Press

the 0button for a zero. Press Jto save.

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

rE INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

Re-enter the Dealer Code.

Press Jto save. Press NEXT (E) button to proceed.

EXIT DEALER PROGRAM MODE: This completes the custom default program. Press the C button to enter the Direct Address Program Mode for further programming or press the Cbutton once again to end all programming and resume normal keypad operation.

9