Monessen Hearth DSSPVMB Connecting the GAS, Flexible Tube Manual Shutoff Gas Supply Inlet Valve

Page 11

CONNECTING THE GAS

NOTICE: A qualified gas appliance installer must connect the heater to the gas supply. Consult all local codes.

CAUTION

Use new black iron or steel pipe. Internally tinned copper or copper tubing can be used per National Fuel Code, section 2.6.3, providing gas meets hydrogen sulfide limits, and where permitted by local codes. Gas piping system must be sized to provide minimum inlet pressure (Listed on Data Plate) at the maximum flow rate (BTU/Hr). Undue pressure loss will occur if the pipe is too small.

A manual shutoff valve must be installed upstream of the appliance. Union tee and plugged 1/8" NPT pressure tapping point should be installed upstream of the appliance. See Figure 4.

To Heater

Pipe Coupling

 

 

 

 

 

Valve

 

Pipe

Locations that the Pressure

 

 

 

 

 

 

 

 

Tapping Point May Be Installed

 

Stainless

 

 

 

Flexible Tube

 

 

 

Manual Shutoff

 

Gas Supply

 

 

Inlet

 

Valve

 

 

 

 

Figure 4 - Gas Connection

IMPORTANT: Hold heater valve firmly with a wrench to prevent movement when connecting to inlet pipe.

CAUTION

CHECK GAS TYPE: The gas supply must be the same as stated on the heater’s rating plate. If the gas supply is different, DO NOT INSTALL THE HEATER. Contact your dealer for the correct model.

Always use an external regulator for all propane/LPG heaters and high pressure one to two-pound natural gas sys- tems only, to reduce the supply tank pressure to a maximum of 13" w.c. This is in addition to the internal regulator in the

heater valve.

46D0550

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Read and Save These Instructions Models Dssnvmb DsspvmbWhat to do if YOU Smell GAS Contents Owner Important Safety InformationInstaller From Cast Iron Stove Product FeaturesMake Sure YOU have Received ALL Parts What YOU will Need for InstallationGetting Started Product Specifications Adequate Combustion and Ventilation AIR General Installation InformationStove Dimensions CodesL1 = 151/2 Ft., L2 = 12 Ft., W = 12 Ft., H = 8 Ft Counter Steel StoveCeiling Mantel Side Wall Floor Clearances / Height RequirmentsFlexible Tube Manual Shutoff Gas Supply Inlet Valve Connecting the GASRemote Receiver Checking GAS Pressure and Connecting Remote ReceiverConnecting Remote Receiver Millivolt Control FigureComplete Millivolt System Check Electrical Wiring MILLI-VOLTConnecting Optional Wall Switch or Thermostat Checking System OperationScrews Installing Thermostat Sensor Option Sold SeparatelyKnob Screws Thermo Bulb Wiring Harnesses Stat Sensor Face PlatePlastic Clip Stat Sensor On/Off Switch Control Knob Optional BlowerOperation of Thermostat Sensor Log #4 Log #2 Back Pins Front LOG PlacementChecking Pilot Flame Flame AP PearanceChecking Burner Flame Operating InstructionsHi/Lo Knob Blower Door Operating InstructionsOptional T-Stat Switch Hi/Lo Control Ignitor/Pilot ControlCleaning and Servicing Operating Instructions and Cleaning and ServicingLogs Replacement Parts ListBurner Assembly Replacement PartsDSS Models Observed Problem Possible Cause Remedy TroubleshootingODS/pilot lights, but flame 46D0550 46D0550 Basic Warranty Lifetime WarrantyFive Year Warranty

DSSPVMB, DSSNVMB specifications

Monessen Hearth has established itself as a reliable name in the realm of home heating solutions, providing innovative products that are both functional and aesthetically pleasing. Among its impressive line-up are the DSSNVMB and DSSPVMB models, which are designed to offer homeowners effective and stylish heating options.

The DSSNVMB (Natural Vent) and DSSPVMB (Propane Vent) are part of Monessen's commitment to creating products that look good while delivering exceptional performance. Both models feature a sleek, modern design that allows them to seamlessly fit into various types of home decor. Their visual appeal, combined with practical utility, makes them a popular choice among homeowners.

One of the most significant features of these models is their efficient venting system. The DSSNVMB utilizes natural venting technology, which allows it to expel exhaust gases through an existing chimney, eliminating the need for external venting systems. This feature not only saves on installation costs but also enhances the overall energy efficiency of the unit. In contrast, the DSSPVMB is designed for propane use, boasting a direct venting system that draws air from outside while expelling gases, creating a closed system that maximizes efficiency and safety.

Both models come equipped with advanced burner technology, ensuring an even and controlled flame that optimizes heat output. This means that homeowners can enjoy consistent warmth without fluctuations in performance. The adjustable flame settings allow users to customize their heating experience to meet individual preferences, creating a tailored comfort level.

Moreover, the DSSNVMB and DSSPVMB are designed with user-friendliness in mind. The easy-to-use control systems allow for straightforward operation, making it simple for homeowners to manage their heating needs. Additionally, these models often come with options for remote control, providing convenience in adjusting the temperature from anywhere in the room.

Safety is a top priority in the design of Monessen's products. The DSSNVMB and DSSPVMB are equipped with built-in safety features, including automatic shut-off systems that activate if any irregularities are detected during operation. This reassurance of safety provides peace of mind for users.

In summary, the Monessen Hearth DSSNVMB and DSSPVMB models exemplify modern home heating solutions that combine efficiency, user-friendliness, and design. With their advanced technologies, stylish appearance, and robust safety features, these units are perfect for any homeowner looking to enhance their living space while enjoying the comfort of efficient heating.
Top Page Image Contents