Monessen Hearth DSSNVMB, DSSPVMB Checking GAS Pressure and Connecting Remote Receiver

Page 12

CHECKING GAS PRESSURE AND CONNECTING REMOTE RECEIVER

WARNING

 

The heater gas inlet connection is 3/8" NPT at the valve. The

Connecting directly to an unregulated

inlet is located on left side of stove. Remove front control plate

 

 

to better access the inlet.

 

propane/L.P.G. tank can cause an

 

 

 

explosion.

When tightening up the joint to the valve, hold the valve securely

 

 

with a wrench to prevent movement.

Test all gas joints from the gas meter to the heater valve for

leaks using a gas analyzer or soap and water solution after completing connection. DO NOT USE AN OPEN FLAME.

Check the gas pressure with the appliance burning and the control set to HIGH.

 

MILLIVOLT CONTROL (FIGURE 5)

Test Port “OUT”

The valve regulator controls the burner pressure which should be checked at the pressure test point.

If outlet pressure is low, check inlet pressure against data plates or manual.

Turn captured slotted screw counter clockwise 2 or 3 turns and then place tubing to pressure gauge over test point (Use test point “OUT” closest to control knob). After taking pressure reading, be sure and turn captured screw clockwise firmly to re-seal. Do not over torque. Check for gas leaks.

NOTE: Remove control panel to access gas valve. Ignitor battery module is located on back of panel.

CONNECTING REMOTE RECEIVER

1.Remove cover on control panel to show opening for remote receiver. See Figure 6.

2.Cut cable to length (approximately 12") for placement in the fireplace.

3.If wires are not stripped, strip back 1/4" of the insulation from free end of each wire. Do not cut off wire connec- tor.

4.Connect two .25 female connectors to the wires at free end of the cable.

5.Insert the wire connector into the receiver. If remote does not have plug-in connector, strip back 1/4" of insulation. Insert wires into terminal and tighten screws.

6.Connect the connectors to the two .25" male connectors located on the left side when facing the unit (Figure 6). Do not let the wires touch the grate or burners.

7.Slide remote receiver in the opening of control panel. Use two screws provided to attach remote receiver to the control panel. See Figure 6.

8.Replace cover with cover supplied with remote. See Figure 6.

NOTE: Do not place remote in combustion chamber.

Figure 5 - Pressure Test Point Location

Milli-Volt Control

Remote

Receiver

Cover ���� ��

����

 

��

���

�

�

�

�

��

Figure 6 - Installing Remote Receiver

12

46D0550

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Models Dssnvmb Dsspvmb What to do if YOU Smell GASRead and Save These Instructions Contents Important Safety Information InstallerOwner From Product Features Cast Iron StoveWhat YOU will Need for Installation Getting StartedMake Sure YOU have Received ALL Parts Product Specifications General Installation Information Stove DimensionsCodes Adequate Combustion and Ventilation AIRCounter Steel Stove L1 = 151/2 Ft., L2 = 12 Ft., W = 12 Ft., H = 8 FtClearances / Height Requirments Ceiling Mantel Side Wall FloorConnecting the GAS Flexible Tube Manual Shutoff Gas Supply Inlet ValveChecking GAS Pressure and Connecting Remote Receiver Connecting Remote ReceiverMillivolt Control Figure Remote ReceiverElectrical Wiring MILLI-VOLT Connecting Optional Wall Switch or ThermostatChecking System Operation Complete Millivolt System CheckInstalling Thermostat Sensor Option Sold Separately Knob Screws Thermo Bulb Wiring Harnesses Stat SensorFace Plate ScrewsStat Sensor On/Off Switch Control Knob Optional Blower Operation of Thermostat SensorPlastic Clip LOG Placement Log #4 Log #2 Back Pins FrontFlame AP Pearance Checking Burner FlameOperating Instructions Checking Pilot FlameOperating Instructions Hi/Lo Knob Blower DoorSwitch Hi/Lo Control Ignitor/Pilot Control Optional T-StatOperating Instructions and Cleaning and Servicing Cleaning and ServicingReplacement Parts List LogsReplacement Parts Burner AssemblyDSS Models Troubleshooting Observed Problem Possible Cause RemedyODS/pilot lights, but flame 46D0550 46D0550 Lifetime Warranty Five Year WarrantyBasic Warranty

DSSPVMB, DSSNVMB specifications

Monessen Hearth has established itself as a reliable name in the realm of home heating solutions, providing innovative products that are both functional and aesthetically pleasing. Among its impressive line-up are the DSSNVMB and DSSPVMB models, which are designed to offer homeowners effective and stylish heating options.

The DSSNVMB (Natural Vent) and DSSPVMB (Propane Vent) are part of Monessen's commitment to creating products that look good while delivering exceptional performance. Both models feature a sleek, modern design that allows them to seamlessly fit into various types of home decor. Their visual appeal, combined with practical utility, makes them a popular choice among homeowners.

One of the most significant features of these models is their efficient venting system. The DSSNVMB utilizes natural venting technology, which allows it to expel exhaust gases through an existing chimney, eliminating the need for external venting systems. This feature not only saves on installation costs but also enhances the overall energy efficiency of the unit. In contrast, the DSSPVMB is designed for propane use, boasting a direct venting system that draws air from outside while expelling gases, creating a closed system that maximizes efficiency and safety.

Both models come equipped with advanced burner technology, ensuring an even and controlled flame that optimizes heat output. This means that homeowners can enjoy consistent warmth without fluctuations in performance. The adjustable flame settings allow users to customize their heating experience to meet individual preferences, creating a tailored comfort level.

Moreover, the DSSNVMB and DSSPVMB are designed with user-friendliness in mind. The easy-to-use control systems allow for straightforward operation, making it simple for homeowners to manage their heating needs. Additionally, these models often come with options for remote control, providing convenience in adjusting the temperature from anywhere in the room.

Safety is a top priority in the design of Monessen's products. The DSSNVMB and DSSPVMB are equipped with built-in safety features, including automatic shut-off systems that activate if any irregularities are detected during operation. This reassurance of safety provides peace of mind for users.

In summary, the Monessen Hearth DSSNVMB and DSSPVMB models exemplify modern home heating solutions that combine efficiency, user-friendliness, and design. With their advanced technologies, stylish appearance, and robust safety features, these units are perfect for any homeowner looking to enhance their living space while enjoying the comfort of efficient heating.
Top Page Image Contents