Napoleon Fireplaces NZ25 Install Ation / Framing, Location and Clearances, See Framing Section

Page 6

6

These options may be incorporated with one another. If the optional blowers are to be installed, make provision dur- ing framing to route a 110 volt power line to the fireplace. Detailed installation instructions are included with each venting kit.

FIGURE 4

LOCATION AND CLEARANCES

The fireplace must be installed against finished walls. Do not install against a vapour barrier or exposed insu- lation.

While the fireplace can be installed directly on the floor, a non-combustible hearth extension is required in front of the fireplace, that must not be built higher than the bottom of the fireplace to avoid air flow blockage. It may therefore be advisable to build the fireplace on a raised platform. The minimum distance between the edge of the fireplace and any adjacent wall, at right angles to it, is 21 inches. A wall projecting at 45° from the outer edge of the fireplace is allowed; projections into this area are permitted. Do not install into any area having a height less than 6 feet (ceil- ing to fireplace bottom, excluding hearth height). See Section on Framing.The location of windows, doors and the traffic flow in the room where the stove is to be located should be considered. If possible, you should choose a location where the chimney will pass through the house without cutting a floor or roof joist.

MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:

0" - FIREPLACE STAND-OFFS (TOP, REAR, & SIDES) 2" - CHIMNEY

1" - HOT AIR GRAVITY DUCTWORK

SEE 'FRAMING' SECTION:

top of unit to ceiling: 32½" - TOP-VENTED ENCLOSURE 44½" - NON-VENTED ENCLOSURE

Clearance from combustibles to furnace hot air duct work as specified by the furnace manufacturer is satis- factory. No additional clearances are required.

Do not pack air space, created between the stand-offs and combustibles, with insulation or any other mate- rial.

Objects placed in front of the fireplace must be kept a minimum of 48" away from the front face of the unit.

INSTALL ATION / FRAMING

FRAMING

The fireplace should be framed using 2x4 lumber as shown in Figure 5. The fireplace should be secured to the floor. Use the pallet packing brackets to accomplish this. If ducting is to be installed, the minimum enclosure ceiling height is 7 feet. Without ducting, the ceiling height may be brought down to a minimum of 6 feet. However a fireplace enclosure with a height less than 7 feet must be provided with sufficient air circulation to avoid a fire hazard. Install ventilation grilles (minimum openings of 40 sq. inches) at both floor and ceiling levels of the enclosure. These grilles must not restrict the flow of heat by more than 25%.

48"

FIGURES 5

WALL

WALL

WALL

WALL

WALL

WS-415-71 /09.07.00

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Solid Fuel Burning Zero Clearance Table of Contents Napoleon Wood Fireplace Presidents Lifetime Limited Warranty Conditions and LimitationsIntroduction General InformationGeneral Instructions Care of Glass and Plated Parts Four OptionsSee Framing Section Install Ation / FramingLocation and Clearances FramingHearth Extension Outside Combustion AIRMantle Clearances Chimney Installation Offset Chimney Installation Installing Flashing and Storm CollarAdding Chimney Sections Firebrick Removal Connection to a Masonry ChimneyIf the Chimney Attaching the HandleBlower Install Ation OptionalNZ25 Features Controlling Combustion AIRFuel Loading and Burn Cycle ASH Removal Procedures Maintenance ReplacementsReplacement Parts Accessories / OptionsTrouble Shooting

NZ25 specifications

The Napoleon Fireplaces NZ25 is a standout option for those looking to enhance their living space with an elegant and efficient heating solution. This stylish fireplace embodies the perfect blend of cutting-edge technology, aesthetic appeal, and practical functionality.

One of the key features of the NZ25 is its impressive heating capacity. Designed for medium to large living areas, the fireplace is capable of producing a remarkable 20,000 BTUs (British Thermal Units) per hour. This potent output makes it an ideal choice for homeowners seeking to maintain a comfortable atmosphere during colder months.

The NZ25 is built with innovative heating technologies that prioritize efficiency. The fireplace utilizes a high-efficiency design, ensuring that a greater portion of the fuel is converted into heat rather than lost through the chimney. As a result, it not only heats your space more effectively but also reduces fuel consumption, making it an eco-friendly option for conscientious consumers.

Moreover, the NZ25 features Napoleon’s Advanced Airflow System, which ensures optimized heat distribution throughout the room. This technology enhances the fireplace's heating capabilities, allowing for consistent warmth and comfort, regardless of where you're seated in the room. Paired with an array of customizable settings, users can effortlessly control the flame and heat output to suit their specific preferences.

The aesthetic appeal of the NZ25 is another highlight. It offers an attractive contemporary design that complements various interior styles, making it a beautiful focal point in any living area. The fireplace can be customized with an assortment of decorative media, which allows homeowners to personalize the look and feel of their space.

Safety is also a top priority with the NZ25. It features a robust safety screen and has been designed to minimize the risk of accidents. With Napoleon’s commitment to quality, the NZ25 is built to last, ensuring that it remains a reliable heating source for years to come.

In summary, the Napoleon Fireplaces NZ25 combines an impressive heating output with modern efficiency technologies and appealing design. Whether for warmth or aesthetics, this fireplace represents an excellent investment for any home.
Top Page Image Contents