Vermont Casting 2477 manual Maintenance, Cleaning the Glass, Adjust the Door Latch

Page 24

Dutchwest Non-Catalytic Convection Heater

Maintenance

Keep Your Stove Looking New

And Working Its Best

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the painted cast iron of your Dutchwest Convection Heater looking new.

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one.

Cleaning the Glass

You will find that most of the carbon deposits on the glass will burn off regularly during hot fires. You can wipe fly ash from the glass when hot using a crumpled piece of dry newspaper. Never use liquid cleaning agents on hot glass. If you wish to clean the glass more thoroughly, follow this procedure:

•Be sure the glass is completely cool.

•Use a glass cleaner especially made for this pur- pose.

•Dry the glass completely.

Adjust the Door Latch

The door latches must close tightly to ensure a good seal between the each door and the stove plates. With time and use, the door latches will require periodic adjustment. Follow this procedure: (Fig. 35)

1.Loosen the small locking nut with an open end wrench.

2.Use the allen wrench (included with the stove) to turn the striker screw clockwise one quarter-turn and close the door to test the engagement. The door latch should engage tightly when closed. Make further adjustments in small increments.

3.When the striker screw is properly adjusted, tighten the small locking nut against the pawl without allow- ing the striker screw to turn.

Small Locking

NutLarge Lock-

ing Nut

Pawl

Striker

Screw

Door

ST806

Fig. 35 Door latch adjustment.

Test and Repair the Door Gaskets

Air leaks can be caused by low spots in the door gas- kets. To locate such low spots, close each door on a slip of paper and attempt to pull the paper free. If the paper slips out without tearing, the gasket isn’t snug enough at that spot.

If the seal cannot be improved by adjusting the door latch, try shimming the gasket. Pack a small quantity of cement or a smaller diameter gasket into the channel beneath the gasket to lift the main gasket and thereby improve its contact with the door frame.

If shimming does not improve the seal, replace the gasket following these steps:

1.Remove the original gasket by grasping an end and pulling firmly.

2.Wearing safety goggles, use a wire brush or the tip of a screwdriver to clean the channel of any remain- ing cement or bits of gasket.

Remove the old gasket by pulling gently, but firmly.

ST440

Fig. 36 Door gasket.

24

30002314

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Non-Catalytic Convection Heater Model Table of Contents Accessories Specifications ModelInstallation Chimney TypesMasonry Chimneys Guidelines for Installing the Chimney Connector Two Types of ConnectorSingle-Wall Connector Prefabricated ChimneysDouble-Wall Connector Assembling Single-Wall Chimney ConnectorSecuring the Connector to a Prefabricated Chimney Securing the Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the Fireplace Fireplace Installations Through the Fireplace Wall Pass-ThroughsFloor Protection CanadaFireplace Installations ProcedureFireplace Installation Clearances ClearancesKeep the Stove a Safe Distance From Surrounding Materials Safe Ways to Reduce ClearancesAlcove Installations Construction RequirementsDesigning a Safe Installation Clearance Chart Reference DiagramsCorner Parallel Installations Stove Clearance Side Rear Chimney Connector ClearanceRight Side OnlyCorner Parallel Installations Chimney Connector Side Rear Dutchwest Convection Heater ModelWall Heat Shield Dimensions DutchWest Non-Catalytic Convection Heater Model #2477Assembly Unpack the PartsAttach the Legs and Heat Shield Fan Kit Installation Heater Controls and Features Air Control OperationDamper Function Successful Wood Burning Burn Only High-Quality FuelLoad Doors Use the Air Control Settings That Work Best for You How to Build and Maintain a Wood Fire Loading WoodBreak-in Fires Lighting the Fire Reloading and Reviving the FireRemove Ashes Frequently Safe Ash HandlingMaintenance Cleaning the GlassAdjust the Door Latch Test and Repair the Door GasketsDamper Adjustment Primary Air Control AdjustmentAvoid Damaging the Glass Door Panel Cleaning the Chimney System Inspect Regularly, Clean As RequiredTWO Weeks Draft Management Draft Testing Single VentingFuel CreosoteDutchwest Convection Heater Dutchwest Convection Heater Limited Lifetime Warranty Months, whichever is longer

2477 specifications

The Vermont Castings 2477 is a highly regarded wood-burning stove that epitomizes both craftsmanship and modern technology, making it a favored choice among wood stove enthusiasts. This powerful yet stylish stove is designed to provide exceptional heating efficiency while enhancing the aesthetic appeal of any living space.

One of the standout features of the Vermont Castings 2477 is its innovative design that combines traditional aesthetics with contemporary functionality. The stove features a large viewing window, allowing for a mesmerizing view of the flames, which creates a warm and inviting ambiance in any room. Its cast iron construction not only adds to the classic look but also ensures durability and long-lasting performance.

The stove has an impressive heat output, capable of heating spaces of up to 2,500 square feet, making it suitable for both small and medium-sized homes. It comes equipped with an efficient EPA-certified combustion system, which dramatically reduces emissions and optimizes fuel use. This technology allows users to enjoy a longer burn time with less firewood, thus enhancing overall efficiency and making it an environmentally friendly option.

The Vermont Castings 2477 features a secondary combustion system that enhances the burning process. By introducing air into the firebox, it ensures that gases are consumed efficiently, resulting in a cleaner burn. The stove is also equipped with a built-in ash pan that simplifies cleanup, allowing users to easily dispose of the ash without the hassle of removing the entire firebox.

In terms of customization, owners appreciate the variety of finishes available, ranging from classic black to vivid enamel colors, allowing for personalization to match different home decors. Additionally, the stove includes adjustable air controls, which enable users to regulate the burn rate and heat output based on their specific needs.

Lastly, installation of the Vermont Castings 2477 is straightforward, and it can be fitted with various chimney configurations, further enhancing its versatility. With its combination of style, technology, and efficiency, the Vermont Castings 2477 wood stove represents an excellent investment for anyone looking to embrace the warmth and charm of a wood-burning heating solution in their home.
Top Page Image Contents