Vermont Casting 2828, 820, 2823, 2825, 2827 Venting System Assembly Natural Vent General Information

Page 19

Vermont Castings Jefferson Direct Vent/Natural Vent Gas Heater

9.Install the storm collar and seal around the joints. (Fig. 31)

10.Add additional vent lengths to achieve the proper overall height.

11.Apply cement to the inner and outer termination collars and install the terminal cap.

Use three #5

 

sheet metal

 

screws at

 

each joint

 

Storm

Sealant

 

Collar

 

 

Upper edge

 

of flange

 

goes under

 

upper

 

shingles

Flashing

 

#7DVSKV

 

(A, B, or F)

 

Roof Support

ST221

Fig. 31 Roof support and flashing.

 

Venting System Assembly - Natural Vent

General Information

The Jefferson Heater is shipped from the factory as a Direct Vent Heater. It may be converted to a Natural Vent heater by installing the Vermont Castings Model Z31D00 FSDHAG Draft Hood Adapter.

The Jefferson Heater is approved for installation as a Natural Vent. CFM Direct Vent pipe could be used directly after the Draft Hood Adapter up to the ceiling, then B-vent pipe must be used. Do not mix types of B- vent pipe; use components from one maker or the other. Follow the vent component makerÕs instructions exactly. The heater will also accept standard or enamelled 7Ó (150mm) diameter pipe, around the Type B venting, for decorative purposes only. (Fig. 32)

NOTE: The restrictor plate supplied with the stove is not used for Natural Vent applications.

The Jefferson stove, when installed as a Natural vent heater, includes a vent safety switch. (Fig. 64, Page 33)

 

Decorative 7Ó

CFM Direct Vent

 

System may be

 

Pipe

 

 

used after Draft

 

4Ó B-vent

Hood up to the

 

Pipe

ceiling.

Draft Hood

 

Adapter

 

 

 

ST358

Fig. 32

Decorative 7Ó pipe may be fitted around the B-vent

pipe.

 

 

Operating the stove when it is not connected to a properly installed and maintained venting system, or tampering with or disconnecting the vent safety switch, can result in carbon monoxide (CO) poisoning and possible death.

For U.S. installations: The venting system must conform with local codes and/or the current National Fuel Gas Code, ANSI Z22.1.

For Canadian installations: The venting system must conform to the current CSA B149.1 installation code.

Install the Vent Pipe

Apply a bead of sealant around bottom end of inner starter pipe (found in bag with logset) and attach to stove. Apply a bead of sealant around top of inner starter pipe and install the Z31D00 FSDHAG Draft Hood according to Draft Hood instructions. (Fig. 33)

Attach the first section of venting to the draft hood. Depending on the length of the individual venting sections and the lengths of the decorative pipe (if installed), you may need to slip the decorative pipe over the venting sections before attaching upper sections to lower ones. The sections of decorative pipe should be oriented with their seams (if any) toward the wall; sections usually do not need to be fastened at each joint, other than slip sections. If the layout includes a slip section, this should be the last section of pipe visible in the room, at the ceiling. Complete the venting according to the vent makerÕs instructions.

20002191

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Jefferson Table Of Contents Installation & Operating Instructions Jefferson dimensions Jefferson Direct Vent/ Natural Vent Stove DimensionsLocating the Stove Installation RequirementsClearance Requirements Hearth Requirements Wall Thimble Centerline from FloorHigh Elevations Gas SpecificationsGas Inlet and Manifold Pressures Horizontal Termination Direct Vent onlyPlate Restictor Plate is used on Direct Vent installations onlyLocation of Vent Termination Vent Termination Clearances Direct Vent onlyGeneral Venting Information Termination Location Canadian Installations US InstallationsHorizontal Run in feet Venting Requirements Natural Vent OnlySupplied with the stove is not used Minimum Horizontal Vent Kit 2792 Venting Requirements and Options Direct Vent onlyUnpack the Stove Assembly ProceduresInstall the Optional Fan Tools RequiredInstall the Vent Adapter Pipe Venting System Assembly Direct Vent General InformationDiscard the inner starter pipe shipped with Install the Restrictor Plate. Consult the ÔVent RunInstall the Outer Adapter Pipe. Apply a 1/4Ó bead Simpson Dura-Vent ComponentsSimpson Dura-Vent install outer adapter pipe Side Wall Termination AssemblyMeasure the horizontal length Vent Termination Below GradeSnorkel kit installation Vertical Through the Roof Vent AssemblyInstall the Vent Pipe Venting System Assembly Natural Vent General InformationAged Logs Install the Log SetBurner Information Air Shutter AdjustmentAir Shutter Adjustment Instructions Connect the Gas Supply LineRemove stove front Complete the Assembly Install the Stove FrontInstall ON/OFF Switch Thermostat This completes assembly of the Jefferson stoveThermostat Connection optional Use only a thermostat rated for 500 millivoltsYour First Fire Flame & Temperature AdjustmentFlame Characteristics OperationTo Turn Off Gas To Heater Lighting And Operating InstructionsSymptom Possible Causes Corrective Action Troubleshooting / Honeywell #8420 Gas Control SystemPilot Type Conversion PrecautionsConversion Procedure Fuel Conversion InstructionsConversion to LP Input BTU/h Conversion to Natural Gas Input BTU/hMaintenance Check the Gas Flame Regularly Gasket ReplacementStove Disassembly Inspect the Vent System AnnuallyBLK Wiring DiagramsDescription Jefferson Direct Vent/Natural Vent Gas HeaterShell Enamel Part Numbers Model Color Fuel Conversion KitsLeft Right Front Number End Decorative Rings Optional AccessoriesRemote Controls Fan KitsLimited Lifetime Warranty

2823, 2825, 820, 2827, 2828 specifications

Vermont Casting stoves are renowned for their quality and performance, with models such as the 2823, 2822, 2828, 820, and 2825 exemplifying the brand’s dedication to craftsmanship and innovation. Each model presents unique features and technologies that cater to different heating needs and preferences.

The 2823 model is a testament to Vermont Casting's commitment to efficiency and style. It boasts a clean-burning gas system that maximizes heat output while minimizing emissions. Additionally, the model's design emphasizes both aesthetic appeal and functionality, making it a perfect centerpiece for any room. With its user-friendly controls, it allows easy adjustments to heat levels, offering a tailored experience for homeowners.

The 2822 model is known for its compact design, making it an ideal choice for smaller spaces. Despite its size, it does not compromise on performance, delivering a substantial heat output. This model is equipped with a dual-burner system that enhances its heating capabilities, ensuring a consistent and comfortable environment. Furthermore, its built-in safety features provide peace of mind, allowing users to enjoy their heating solution with confidence.

In contrast, the 2828 model offers a higher output, perfect for larger areas. Its innovative heat exchanger technology ensures optimal heat distribution throughout the space, making it a favorite among those with bigger homes. The model’s sleek design and customizable options allow homeowners to choose finishes that complement their existing decor, enhancing both the visual and functional aspects of their living areas.

The 820 model stands out with its unique style, offering a combination of traditional and modern aesthetics. This model features a powerful combustion system that maximizes efficiency while reducing fuel consumption. Its large viewing window provides a beautiful fire display, turning any space into a cozy retreat. The 820 is particularly favored among users who appreciate the ambiance of a traditional fireplace with the convenience of modern technology.

Finally, the 2825 model is designed for users seeking maximum customization. Its adjustable heating options and multiple finish choices allow homeowners to create a truly personalized experience. The advanced technology incorporated into the 2825 ensures enhanced performance, making it one of the most sought-after models in the Vermont Casting lineup.

In summary, the Vermont Casting 2823, 2822, 2828, 820, and 2825 models each have their unique features that cater to different heating needs. With advanced combustion technologies, customizable designs, and a commitment to efficiency, these stoves highlight Vermont Casting's reputation for quality and innovation in home heating solutions.
Top Page Image Contents