Vermont Casting 3349 Parallel Installation Minimum Clearance Flue Centerline, Ceiling Clearances

Page 5

Clearance Requirements

Minimum Clearances to

Combustible Materials

Measure side clearances as shown in Figures 2 through 5 from the outer edge of the cast iron stove top. Measure rear clearances from the rear sheet metal shroud.

The Radiance heater is approved for installation into an alcove constructed of combustible materials to the dimensions and clearances shown on this page.

The same clearances apply in a standard parallel installation.

Parallel Installation: Minimum Clearance

and Flue Centerline

C

L

C

D

A

C

L

B

Stove Clearance

A: 4” (100mm)

 

 

B: 6” (150mm)

 

Pipe Centerline

C: 21⁷⁄₈“ (556mm)

 

 

D: 8¹⁄₂” (216mm)

ST128b

Fig. 2 Parallel installation, minimum back and side clear- ances, and flue centerlines.

Corner Installation: Minimum

Clearance and Flue Centerline

B

A

B

A

Stove Clearance:

A: 6” (150mm)

Pipe Centerline:

B: 18” (460mm)

ST129b

Fig. 3 Corner installation requirements.

Radiance Natural Vent Gas Heater

Ceiling Clearances

46"

(1168mm)

74"

(1880mm)

R A D I A N C E

ST131b

Fig. 4 Minimum ceiling clearance: minimum alcove height.

Alcove Minimum Dimensions

42"

(1070mm)

4"

(100mm)

6"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(150mm)

 

 

 

 

 

 

 

 

 

 

 

 

(150mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 5 The Radiance Natural Vent Stove is approved for installation into alcoves built of combustible materials.

Hearth Requirements

The Radiance Heater must be installed on rigid floor- ing. When the heater is installed directly on any combustible surface other than wood flooring, a metal or wood panel extending the full width and depth of the unit must be used as the hearth. There are no other hearth requirements.

WARNING:

• Always maintain required clearances (air spaces) to nearby combustibles to prevent fire hazard. Do not fill air spaces with insulation. All venting components must maintain a 1" (25mm) clearance to combustible materials. Maintain a 6” (150mm) clearance when using single wall pipe.

The gas appliance and vent system must be vented directly to the outside of the building and never be attached to a chimney serving a separate solid fuel or gas-burning appliance.

Refer to the manufacturer's instructions included with the venting system for complete installation procedures.

20004409

5

Image 5
Contents Radiance Table of Contents Installation & Operating Instructions Radiance dimensions Stove DimensionsCorner Installation Minimum Clearance and Flue Centerline Parallel Installation Minimum Clearance Flue CenterlineAlcove Minimum Dimensions Ceiling ClearancesGas Inlet and Manifold Pressures Gas SpecificationsHigh Elevations Venting Requirements and OptionsVenting Requirements Passing Through a Combustible Wall or CeilingAssembly Procedures Remove/replace rear shroud Attach rear shroud cover plate to the rear shroud Attach rheostat to left side of valve Attach the B-vent adapter to the flue Venting System AssemblyConnect the Gas Supply Line Install ON/OFF SwitchBurner Information Order to connect Natural Gas, use a fitting with aInstall Rear Bracket and Log Set Install the Mesh and GrilleThermostat Connection optional Aged LogsTop View Operation What to do if YOU Smell GAS Lighting and Operating InstructionsTo Turn Off Gas To Heater Symptom Possible Causes Corrective Action Troubleshooting / Honeywell #8420 Gas Control SystemFuel Conversion Instructions Conversion PrecautionsConversion Procedure Injector Orifice Size Matrix Air Shutter AdjustmentConversion to Natural Gas Input BTU/h Conversion to LP Input BTU/hMaintenance Check the Gas Flame Regularly Gasket ReplacementInspect the Vent System Annually BLK Wiring DiagramsRadiance Natural Vent Gas Heater Rnvod Rnvod DescriptionShell Enamel Part Numbers Fuel Conversion KitsOptional Accessories Radiance Natural Vent Gas Heater Radiance Natural Vent Gas Heater If Warranty Service is NEEDED… Product Covered by this WarrantyProduit Couvert PAR LA Présente Garantie SI UN Service Sous Garantie EST REQUIS…CFM Specialty Home Products

3356 4409 410, 3340, 3355, 3349 specifications

Vermont Castings offers a diverse lineup of wood stoves designed to provide warmth, efficiency, and aesthetic appeal to any home. Among their impressive models are the 3355, 3340, 3356, 4409, 410, and 3349, each featuring unique characteristics that cater to various heating needs and preferences.

The Vermont Castings 3355 model stands out for its large firebox and high-efficiency design, making it an excellent choice for those seeking extended burn times. This model employs a catalytic combustor that enhances fuel efficiency while minimizing emissions, allowing you to enjoy heat from fewer logs. Its classic design complements traditional and modern aesthetics alike.

The 3340 model emphasizes versatility and functionality. With adjustable airflow controls, users can customize the heat output to suit their needs. A notable feature of this model is its built-in ash pan, simplifying maintenance and cleanup. The durable construction ensures longevity, while the beautiful cast iron exterior makes it a focal point in any room.

For those seeking a more compact option, the 3356 model is an ideal choice. This wood stove features a smaller footprint without sacrificing performance. Designed for smaller spaces, its efficient heating capabilities and elegant detailing provide warmth without overwhelming your living area. It also incorporates Vermont Castings’ advanced clean-burning technology, ensuring reduced emissions and a more sustainable heating solution.

The 4409 model, known for its robust output, is perfect for larger homes or open spaces. Its impressive heating capacity, combined with the brand’s signature craftsmanship, allows for effective warming even in the coldest climates. Furthermore, the 4409 features a unique top-loading design, making it easy to refuel without interrupting the warmth.

The 410 model is a modern take on traditional wood stoves, offering an eye-catching contemporary design that easily integrates into any decor. This model combines cutting-edge technology with user-friendly features, like easy-loading doors and a large viewing window to enjoy the dancing flames.

Lastly, the 3349 is designed for optimal performance with a focus on efficiency and sustainability. This model is equipped with a clean-burning system that significantly reduces particulate emissions, making it eco-friendly. It also boasts a spacious firebox that accommodates larger logs for longer burn times, maximizing heat output while minimizing wood consumption.

In summary, Vermont Castings offers a variety of wood stoves, such as the 3355, 3340, 3356, 4409, 410, and 3349, each with unique features and technologies. Their commitment to performance, efficiency, and elegant design ensures that there is a perfect fit for every heating need, providing both warmth and style for your home.