Vermont Casting 2310 Operation, Vigilant Controls Thermostat Lever, Damper, Fuel

Page 16

Vermont Castings Vigilant

Operation

The Vigilant Controls

The Thermostat Lever

Adjust the thermostat lever to control the heat level. Move the thermostat lever to the left to make the fire burn hotter. Move it to the right for less heat.

The thermostat regulates the heat level when the stove is operating by controlling the amount of combustion air entering the stove. The heat level is based on the setting of the thermostat lever and the strength of your chimney’s draft. (Refer to Page 4 for more information

on draft.)

Less Heat

More Heat

 

Thermostat

Rear View

Lever

 

 

Thermostat

Air Inlet Flap

Air Inlet

ST697

Fig. 22 The components that regulate incoming air.

The Damper

Use the internal damper to control the direction of ex- haust flow within the stove.

When the damper is open, smoke goes directly to the chimney. The resulting heat warms the chimney and helps develop and maintain the strongest draft.

When the damper is closed, smoke —and heat— is held in the stove longer. This results in more heat radi- ated into the room and less heat going up the chimney.

The Vigilant II Coal Stove may be set for a long burn with the damper either open or closed. However, some chimneys may require the extra heat provided when the damper is open for best operation.

The thermostat lever will continue to control the amount of combustion air entering the stove to ensure a steady

heat output.

Fuel

High quality fuel gives best results

Pea or nut-sized coal, either anthracite or bituminous, may be burned. Anthracite coal that has a low ash content will provide more heat with less ash than most other types of coal. Your fuel dealer may be able to provide you with information about the ash content of the coal he sells.

The Vigilant II Coal Stove is designed to burn anthracite (hard coal) or bituminous coal (soft coal). Do not burn other fuels. As shipped from the factory it is set up to burn bituminous coal.

If you wish to burn anthracite, call your Vermont Cast- ings Authorized Dealer, and request that your stove be modified to burn anthracite. The dealer will make the modification and attach a label to the top of the ash door stating that the stove has been modified to burn anthracite, and warning against burning bituminous coal in the modified stove. If your stove has the label attached to the top of the ash door, it has already been modified.

Do not burn bituminous coal in a stove which has been modified to burn anthracite. Burning bituminous coal in a stove which has been modified to burn anthracite could cause very high temperatures and create a haz- ardous condition.

Coal should be stored under cover to maintain dryness. Even for short term storage, keep coal a safe distance from the heater and keep containers of coal out of the areas around the heater used for refueling and ash

removal.

Starting a Coal Fire

The most important step to a successful coal fire is to build a thick bed of hardwood or charcoal briquette coals on the grates. Coal requires a high ignition temperature compared to wood, and a concentrated ember bed is necessary to get a coal fire going. In ad- dition, the heat produced during this step is necessary to warm the flue and establish a strong draft.

Follow this procedure to start a coal fire:

1.Cover the grates with crumpled newspaper. Add a layer of short, finger-sized kindling wood, preferably hardwood. NOTE: Do not build the fire close to the glass. Open the damper, close the griddle, and move the thermostat lever to the left.

2.Light the paper, and once the kindling is burning briskly, add a layer of larger wood or untreated charcoal.

16

2000898

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Vigilant Table of Contents WelcomeSpecifications Vigilant II Coal Stove Model #2310Installation Codes and ListingsChimneys and Draft Improving Draft With Outside AirNew Chimneys Chimney GuidelinesExisting Chimneys Prefabricated Chimney SizeMasonry Using The Clearance Chart ClearancesClearance Reductions Unprotected Walls Clearances With No Heat ShieldsMinimum clearance, corner installation, no heat shield Clearances With Only Stove Rear Heat ShieldProtected Walls Wall shield con- structionVigilant II Clearance Chart All InstallationsStove in Corner Stove Installed Par Allel to WallFloor Protection for Fireplace Installations Floor Protection Freestanding InstallationsFireplace Mantel and Trim Clearance Chimney Connectors Wall Pass-ThroughsInstallation Procedures Setting Up the Stove Chimney Connector DampersChimney Connector Assembly Removable HandleSecuring the Connector to Masonry Chimney Securing the Connector to a Prefabricated ChimneyAbove a fireplace Through a fireplace Operation Vigilant Controls Thermostat LeverDamper FuelDaily Operation Surface Thermometer Internal DamperReloading the Stove Important Warm-weather ConsiderationsRemove Ash Regularly Dispose of Ash SafelyMaintenance Cleaning Cast IronCleaning Porcelain Enamel Adjusting The Door LatchClean-Out Access Covers Interior PartsClean the Glass as Needed How to Replace Damaged GlassReplace Thermostat Assembly Remove the Old Thermostat AssemblyAdjust the Chain Length Chimney SystemDraft Problems Safety TipsVigilant Coal Vigilant Coal ModelVermont Castings Vigilant How To Obtain Service Limited One Year WarrantyExclusions and Limitations CFM Corporation

2310 specifications

Vermont Casting 2310 is a celebrated addition to the family of cast-iron wood stoves, combining vintage charm with modern functionality. It boasts both aesthetic appeal and superior heating capabilities, making it a popular choice for homeowners seeking an efficient and reliable heating solution.

One of the main features of the Vermont Casting 2310 is its robust construction, utilizing high-quality cast iron renowned for excellent heat retention and distribution. This material not only ensures durability but also adds to the stove's timeless appearance. The 2310 model is elegantly designed with clean lines and a classic finish, available in various colors to complement any home decor.

The Vermont Casting 2310 is equipped with advanced technology that enhances its performance. One such feature is its efficient combustion system, which promotes a cleaner burn by maximizing fuel utilization. This results in fewer emissions and less creosote buildup, making it an environmentally friendly option. The air wash system keeps the glass door clean, ensuring you always have a clear view of the beautiful flames, enhancing the cozy atmosphere that a wood stove brings to any space.

Another standout characteristic of the 2310 is its adaptability. It can accommodate a range of firewood sizes and types, allowing users to choose the most convenient and economical fuel sources. Additionally, the stove features a convenient ash pan that simplifies clean-up, making maintenance hassle-free.

The Vermont Casting 2310 is designed with user comfort in mind. The large firebox provides ample space for fuel, extending burn times and requiring less frequent loading. The adjustable airflow controls allow users to customize heat output, giving them complete control over their heating needs.

Safety is also a priority in the design of the 2310, with features like a built-in thermostat and a safety shut-off system. These features ensure optimal operation and peace of mind, so you can enjoy the warmth and glow of your wood stove without worry.

Overall, the Vermont Casting 2310 combines classic design with modern technology, offering efficiency, reliability, and aesthetic appeal. Whether heating a cabin in the woods or enhancing a family home's ambiance, it stands out as a top choice for wood-burning enthusiasts.
Top Page Image Contents