Vermont Casting 410 Madison Control Settings, Starting and Maintaining a Fire

Page 18

Madison Woodburning Stove

In newer homes that are well-insulated and weather- tight, poor draft may result from insufficient air in the house. In such cases, a slightly opened window near the stove on the windward side of the house will provide the fresh air needed.

A more effective option for delivering ample combustion air to the stove is to duct air directly from outdoors to the stove. In fact, in some areas, provisions for outside combustion air are required in all new construction. The optional Madison Outside Air Adapter is available from your dealer.

When you first begin using the stove, pay attention to the air control settings. You will quickly find that a specific setting will give you a fixed amount of heat. It may take some time to determine the amount of heat and the length of burn you should expect from various settings.

Do not for any reason attempt to increase the firing of your heater by altering the air control adjustment range outlined in these directions.

Use the following air control settings as a starting point to help determine the best settings for your installation.

Madison Control Settings

Burn Rate

Primary Air Control

Shutter Position

High

Left most position

Fully Open

Medium

 

Half Open

Low

Right most position

Fully Closed

Before you begin using the stove, please read the Appendix on Draft Management, starting on Page 22, to learn how the characteristics of your particular installation will affect your stove's performance. You and the stove are parts of a system; other parts of the system have a strong effect on performance. You may need to vary your firing technique to get the results you desire.

Starting and Maintaining a Fire

Conditioning Your Stove

Cast iron is extremely strong, but it can be broken with a sharp blow from a hammer or from the thermal shock of rapid and extreme temperature change.

The cast plates expand and contract with changes in temperature. When you first begin using your Madison, minimize thermal stress by allowing the plates to adjust gradually during three or four initial break-in fires following Steps 1- 3.

BURN SOLID WOOD FUEL ONLY, AND BURN IT DIRECTLY ON THE GRATE. DO NOT ELEVATE THE FUEL. DO NOT BURN COAL OR OTHER FUELS.

WARNING: OPERATE THIS STOVE ONLY WITH THE DOORS FULLY CLOSED.

The Primary Air Inlet must be open when starting a fire or when refueling.

Step 1. Open the primary air control fully. (Lever at left most position)

Step 2. Place several sheets of crumpled newspaper in the stove. Avoid using glossy or colored paper, as these burn poorly. At the front of the firebox, place on the paper six or eight pieces of dry kindling split to a finger-width size, and on the kindling lay two or three larger sticks of split dry wood approximately 1- 2" (25-51mm) in diameter. (Fig. 27)

 

ST263

Fig. 27

Start a fire with small, dry kindling.

Step 3. Light the newspaper and close the doors. Gradually build up the fire by adding a few 3-5" (80- 120 mm) diameter splits. (Fig. 28) If this is one of the first few "break-in" fires, let the fire burn brightly, and then let it die out.

•During the break-in fires, don't let the stove get hotter than 500°F. (260°C) as measured on an optional stove-top thermometer. Adjust the air control lever as necessary to control the fire.

•Some odor from the stove’s hot metal, the paint, and the cement is normal for the first few fires.

ST264

Fig. 28 Gradually add larger pieces of wood until all the wood is burning well.

18

30001453

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Madison Table of Contents AccessoriesIntroduction Specifications Madison, Model 1655 SeriesInstallation ChimneysMasonry Chimneys Chimney Connector Guidelines Prefabricated ChimneysChimney Size Securing the Single-wall Connector to a Masonry Chimney Double-wall Chimney ConnectorsSingle-wall Chimney Connectors Freestanding InstallationsConnection Above the Fireplace Wall Pass-throughsRequirements Canadian Requirements Floor ProtectionFireplace Hearth Protection Clearance to Surrounding Combustible MaterialsSafe Ways to Reduce Clearances Wall Shields Approved Wall shield constructionAlcove Installations Construction RequirementsMadison 1655 Series Clearance Chart Stove ClearanceMadison 1655 Series Clearance Diagram Unprotected Surfaces ProtectedST563 Assembly Install the Outside Air Adapter With Rear Heat ShieldHow the Madison Works Use the Air Control Setting that Works Best for YouOperation Burn Only High-Quality WoodMadison Control Settings Starting and Maintaining a FireRefuel While the Embers Are Still Hot Ash DisposalSmoke Detectors Maintenance Care of the Cast Iron SurfaceAnnual Maintenance Clean the Primary Air OutletChimney System Creosote Inside/Outside Location Draft ManagementSteel Chimney Flue SizingBackpuffing Single VentingFuel Negative PressureMadison Woodburning Stove Madison Woodburning Stove Shell Enamel Parts Madison Model Warranty CFM Specialty Home Products

410 specifications

Vermont Casting 410 is an innovative wood-burning stove that exemplifies the perfect blend of traditional craftsmanship and modern technology. Known for its high efficiency and aesthetic appeal, it offers a reliable heating solution for homes of varying sizes.

One of the main features of the Vermont Casting 410 is its robust construction, made from high-quality cast iron that not only enhances durability but also retains heat effectively. This material ensures that the stove can withstand high temperatures while providing a steady and even heat distribution, making it an ideal choice for homeowners seeking consistent warmth throughout colder months.

The Vermont Casting 410 incorporates advanced combustion technology, which significantly improves its efficiency and lowers emissions. With its CleanBurn technology, this stove generates more heat while consuming less fuel. This results in a longer burn time and minimized wood usage, making it an eco-friendly choice for both the environment and homeowners looking to reduce heating costs.

The versatile design of the Vermont Casting 410 allows it to complement a wide range of interior styles. It features a classic cast iron finish with various color options, enabling users to select a look that suits their home decor. The large viewing window provides a mesmerizing view of the flames, creating a cozy and inviting atmosphere.

Another standout aspect of the Vermont Casting 410 is its easy-to-use features. The stove comes with a simple air control system that allows users to adjust the combustion airflow, optimizing the burn rate based on individual heating needs. This control not only enhances efficiency but also simplifies the operation of the stove, making it user-friendly even for those who are new to wood-burning appliances.

In terms of installation, the Vermont Casting 410 is designed for straightforward setup. It can be connected to existing flue systems, with options for both direct venting and traditional chimney configurations. This flexibility gives homeowners the option to enhance their current heating setup without extensive renovations.

Overall, the Vermont Casting 410 stands out as a reliable, efficient, and stylish wood-burning stove. With its emphasis on quality materials, advanced technology, and user-friendly features, it provides an excellent heating solution while contributing to the comfort and charm of any home. Whether for ambiance or functionality, Vermont Casting 410 exemplifies the essence of modern wood-burning stoves.
Top Page Image Contents