Vermont Casting 410 Chimney System Creosote, Annual Maintenance, Clean the Primary Air Outlet

Page 21

The Chimney System

Creosote

Your Madison is designed to reduce creosote buildup significantly. However, regular chimney inspection and maintenance must still be performed. For safety, good stove performance, and to protect your chimney and chimney connector, inspect your chimney and chimney connector on a regular schedule. Clean the system if necessary. Failure to keep the chimney and connector system clean can result in a serious chimney fire.

When wood is burned slowly, it produces tar, organic vapors and moisture that combine to form creosote. The creosote vapors condense in the relatively cool chimney flue. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire within the flue system that can damage the chim- ney and overheat adjacent combustible material.

If you do have a chimney fire, promptly:

•Close the thermostat lever.

•Get everyone out of the house.

•Call the Fire Department.

You should inspect the system every two weeks during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the stove cool completely. Then, using a mirror and a strong light, sight up through the flue collar into the chimney flue. If it is not possible to inspect the flue system in this fashion, the stove must be disconnected to provide better viewing access.

If a significant layer of creosote has accumulated — 1/8" (3mm) or more — remove it to reduce the risk of a chimney fire.

Clean the chimney using a brush the same size and shape as the flue liner. Flexible fiberglass rods are used to run the brush up and down the liner, causing any deposits to fall to the bottom of the chimney where they can be removed through the clean-out door.

The chimney connector should be cleaned by disconnecting the sections, taking them outside, and removing any deposits with a stiff wire brush. Reinstall the connector sections after cleaning, being sure to secure the individual sections with sheet metal screws.

If you cannot inspect or clean the chimney yourself, contact your local Vermont Castings’ Authorized Dealer or hire a professional chimney sweep.

Madison Woodburning Stove

Annual Maintenance

Perform a thorough cleaning, inspection and repair each Spring, at the end of the heating season.

•Thoroughly clean the chimney and chimney connec- tor.

•Inspect the chimney for damage and deterioration. Replace weak sections of prefabricated chimney. Have a mason make repairs to a masonry chimney.

•Inspect the chimney connector and replace any damaged sections.

•Clean ash debris from under the primary air plate. See procedure below.

•Check gasketing for wear or compression, and replace if necessary. A 'paper test' will guide you on this. Close and lock the door on a slip of paper and then try to pull the paper out. If the paper pulls out with little or no resistance, the gasket isn't snug enough at that spot. If adjusting the latch doesn't result in a seal that makes it hard to pull the paper out, replace the gasketing.

•Check door handle for tightness. Adjust if needed.

•Check heat shield screws. Tighten as necessary.

•Clean dust from the inner sides of bottom, rear and connector heat shields.

•Remove ashes from the ash pan and replace with moisture absorbing material (such as cat litter) to keep the stove interior dry. Close the stove door to keep cats from using the litter.

•Touch up the paint on black stoves.

Clean the Primary Air Outlet

1.Remove the phillips head screws that retain the Primary Air Plate.

2.Use a screwdriver to pry the plate out of the ce- mented seams.

3.Remove ash debris from the cavity.

4.Use high-temperature furnace cement to reseal the front seam and side seams and replace the plate. Secure with the phillips head screws.

30001453

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Madison Table of Contents AccessoriesIntroduction Madison, Model 1655 Series SpecificationsInstallation ChimneysMasonry Chimneys Chimney Connector Guidelines Prefabricated ChimneysChimney Size Single-wall Chimney Connectors Double-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsConnection Above the Fireplace Wall Pass-throughsRequirements Floor Protection Canadian RequirementsFireplace Hearth Protection Clearance to Surrounding Combustible MaterialsSafe Ways to Reduce Clearances Approved Wall shield construction Wall ShieldsConstruction Requirements Alcove InstallationsStove Clearance Madison 1655 Series Clearance ChartUnprotected Surfaces Protected Madison 1655 Series Clearance DiagramST563 Assembly With Rear Heat Shield Install the Outside Air AdapterOperation Use the Air Control Setting that Works Best for YouHow the Madison Works Burn Only High-Quality WoodStarting and Maintaining a Fire Madison Control SettingsRefuel While the Embers Are Still Hot Ash DisposalSmoke Detectors Care of the Cast Iron Surface MaintenanceAnnual Maintenance Clean the Primary Air OutletChimney System Creosote Steel Chimney Draft ManagementInside/Outside Location Flue SizingFuel Single VentingBackpuffing Negative PressureMadison Woodburning Stove Madison Woodburning Stove Shell Enamel Parts Madison Model Warranty CFM Specialty Home Products

410 specifications

Vermont Casting 410 is an innovative wood-burning stove that exemplifies the perfect blend of traditional craftsmanship and modern technology. Known for its high efficiency and aesthetic appeal, it offers a reliable heating solution for homes of varying sizes.

One of the main features of the Vermont Casting 410 is its robust construction, made from high-quality cast iron that not only enhances durability but also retains heat effectively. This material ensures that the stove can withstand high temperatures while providing a steady and even heat distribution, making it an ideal choice for homeowners seeking consistent warmth throughout colder months.

The Vermont Casting 410 incorporates advanced combustion technology, which significantly improves its efficiency and lowers emissions. With its CleanBurn technology, this stove generates more heat while consuming less fuel. This results in a longer burn time and minimized wood usage, making it an eco-friendly choice for both the environment and homeowners looking to reduce heating costs.

The versatile design of the Vermont Casting 410 allows it to complement a wide range of interior styles. It features a classic cast iron finish with various color options, enabling users to select a look that suits their home decor. The large viewing window provides a mesmerizing view of the flames, creating a cozy and inviting atmosphere.

Another standout aspect of the Vermont Casting 410 is its easy-to-use features. The stove comes with a simple air control system that allows users to adjust the combustion airflow, optimizing the burn rate based on individual heating needs. This control not only enhances efficiency but also simplifies the operation of the stove, making it user-friendly even for those who are new to wood-burning appliances.

In terms of installation, the Vermont Casting 410 is designed for straightforward setup. It can be connected to existing flue systems, with options for both direct venting and traditional chimney configurations. This flexibility gives homeowners the option to enhance their current heating setup without extensive renovations.

Overall, the Vermont Casting 410 stands out as a reliable, efficient, and stylish wood-burning stove. With its emphasis on quality materials, advanced technology, and user-friendly features, it provides an excellent heating solution while contributing to the comfort and charm of any home. Whether for ambiance or functionality, Vermont Casting 410 exemplifies the essence of modern wood-burning stoves.
Top Page Image Contents