Vermont Casting 1920 installation instructions Installation, Masonry Chimneys

Page 4

Aspen Woodburning Stove

Installation

SAFETY NOTICE: IF YOUR STOVE IS NOT PROP- ERLY INSTALLED, OPERATED AND MAINTAINED, A HOUSE FIRE MAY RESULT. FOR SAFETY, FOLLOW ALL INSTALLATION, OPERATION AND MAINTE- NANCE DIRECTIONS. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTAL- LATION INSPECTION REQUIREMENTS IN YOUR AREA.

Before you begin an installation, review your plans to be certain that:

•Your stove and chimney connector will be far enough from combustible material to meet all clearance requirements.

•The floor protector is large enough and is constructed properly to meet all requirements.

•You have all necessary permits from local authorities.

Your local building official is the final authority for ap- proving your installation as safe and determining that it meets local and state codes.

The metal label permanently attached to the back of the stove indicates that the Aspen has been tested to current UL and ULC standards by Intertek Testing Ser- vices of Middleton, Wisconsin. Clearance and installa- tion information is also printed on the label. Local au- thorities generally will accept the label as evidence that, when the stove is installed according to the information on the label and in this manual, the installation meets codes and can be approved. Codes, however, vary in different areas. Before starting the installation, review your plans with the local building authority. Your local dealer can provide any additional information needed.

For any unresolved questions about installation, refer to the National Fire Protection Association’s publication ANSI/NFPA 211–1988 Standard for Chimneys, Fire- places, Vents and Solid Fuel Burning Appliances. In Canada, the equivalent publication is CSA CAN-B365, Installation Code for Solid Fuel Burning Appliances and Equipment. These standards are the bases for many national codes. They are nationally recognized and are accepted by most local authorities. Your local dealer or your local building official may have a copy of these regulations.

IMPORTANT: Failure to follow these installation instructions may result in a dangerous situation, in- cluding a chimney or house fire. Follow all instruc- tions exactly and do not allow makeshift compro- mises to endanger property and personal safety.

Chimneys

Your stove must be connected either to a sound masonry chimney that meets local codes, to a relined masonry chimney that meets local codes, or to an approved prefabricated metal chimney. Whichever of those types you use, the chimney and chimney connec- tor must be in good condition and kept clean.

If you use an existing masonry chimney, it must be inspected to ensure safe condition before the stove is installed. Your local professional chimney sweep, build- ing inspector, or fire department official will be able to make the inspection or direct you to someone who can.

The chimney should extend at least 3’ (914 mm) above the highest point where it passes through a roof, and at least 2’ (610 mm) higher than any portion of a building within 10’ (3 m).

To assure proper draft and good performance, any chimney used with this stove should extend at least 16’ (4.9 m) above the flue collar of the stove.

0 To 10'

 

2' Min. 3'

0 To 10'

Min.

 

 

2' Min. 3'

 

Min.

Reference Point

AC617

 

Fig. 2 The 2’-3’-10’ Chimney Rule.

 

Masonry Chimneys

An existing masonry chimney must be inspected to con- firm that it has a lining. Do not use an unlined chimney. The chimney also should be examined for cracks, loose mortar, other signs of deterioration, and blockage. Repair any defects before the chimney is used with your stove.

A prefabricated double- wall insulated chimney

A tile-lined masonry chimney

ST241

Fig. 3 Standard Chimney Types

4

30000369

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Aspen Table of Contents IntroductionSpecifications Aspen, ModelChimneys InstallationMasonry Chimneys Chimney Connector Guidelines Prefabricated ChimneysChimney Size Masonry Chimneys, cont’dDouble-wall Chimney Connectors Single-wall Chimney ConnectorsSecuring the Single-wall Connector To a Masonry Chimney Freestanding InstallationsConnection Through the Fireplace Connection Above the FireplaceWall Pass-throughs Canadian Requirements RequirementsAlternate methods approved by the Nfpa Fireplace Hearth Protection Floor ProtectionCanada Clearance to Surrounding Combustible Materials Mobile Home InstallationSafe Ways to Reduce Clearances Wall Shields Approved Wall shield constructionFireplace Clearances Alcove ClearancesAspen Clearance Chart Front Clearance All Installations To CombustiblesStove Installed Stove in Corner Parallel to Wall Assembly Install Stove LegsInstall the Ashlip Install the Outside Air AdapterInstall the Bottom Heat Shield Install the Rear Heat ShieldFlue Collar Reversal Use the Air Control Setting That Works Best for You OperationHow the Aspen Works Burn Only High-Quality WoodAspen Control Settings Burn Rate Primary Air Control Starting and Maintaining a Fire Conditioning Your StoveRefuel While the Embers Are Still Hot Start a fire with small, dry kindlingAsh Disposal Smoke DetectorsMaintenance Cleaning the GlassGlass Replacement Care of the Cast Iron SurfaceAdjust the Door Gasket ReplacementCreosote Annual Maintenance Clean the Primary Air OutletDraft Management Masonry ChimneySteel Chimney Inside/Outside LocationDraft Testing Pipe & Chimney LayoutSingle Venting FuelNegative Pressure ConclusionAspen Woodburning Stove Aspen Woodburning Stove Model Aspen Woodburning Stove Aspen Woodburning Stove Warranty CFM Corporation

1920 specifications

Vermont Castings has long been a beacon of quality and craftsmanship in the world of cast iron products, particularly known for its wood and gas stoves, as well as outdoor grills. Established in the mid-1970s, Vermont Castings quickly rose to prominence for their superior heating efficiency and durability, but it's important to highlight that their iconic brand rests on decades of innovation and tradition.

The Vermont Castings 1920 model is reminiscent of the vintage designs that reflect a commitment to both aesthetics and functionality. This model features a robust cast iron construction, ensuring exceptional heat retention and an impressive lifespan. Cast iron is known for its excellent ability to radiate warmth evenly, making it highly effective for heating spaces.

One of the standout features of the Vermont Castings 1920 is its efficient wood-burning abilities. Equipped with a patented catalytic combustor, this model can achieve impressive efficiency ratings, which translate to fewer emissions and lower wood consumption. This technology not only honors environmental standards but also enhances the overall user experience. The combustor maximizes the burn time, allowing users to enjoy a more extended period of warmth without the need for constant refueling.

The design of the 1920 model pays homage to classic aesthetics, featuring intricate detailing and a timeless finish that complements a variety of interior styles. It's available in multiple colors, allowing homeowners to select a look that best fits their décor. The large glass window on the front lets users enjoy the mesmerizing flames while ensuring the stove remains safe and efficient.

Ease of use is another critical characteristic of the Vermont Castings 1920. It incorporates straightforward controls for adjusting airflow, enabling users to fine-tune the burn rate and optimize heat output. Furthermore, the stove features an easy-to-clean ash pan, making maintenance a breeze.

Overall, the Vermont Castings 1920 model embodies a blend of historical craftsmanship and modern technology, providing an unparalleled heating solution with aesthetic appeal. Its enduring features and innovative attributes ensure that it remains a favorite among those seeking both functionality and style in home heating solutions. Whether in a rustic cabin or a contemporary home, the 1920 model stands out as a testament to the elegance and efficiency that Vermont Castings is known for.
Top Page Image Contents