Vermont Casting 1640 installation instructions Installation, Masonry Chimneys

Page 4

Intrepid 1640 Woodburning Stove

Installation

SAFETY NOTICE: IF YOUR STOVE IS NOT PROP- ERLY INSTALLED, OPERATED AND MAINTAINED, A HOUSE FIRE MAY RESULT. FOR SAFETY, FOLLOW ALL INSTALLATION, OPERATION AND MAINTENANCE DIRECTIONS. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND IN∝.

Before you begin an installation, review your plans to be certain that:

•Your stove and chimney connector will be far enough from combustible material to meet all clearance requirements.

•The floor protector is large enough and is con- structed properly to meet all requirements.

•You have all necessary permits from local authori- ties.

Your local building official is the final authority for approving your installation as safe and determining that it meets local and state codes.

The metal label permanently attached to the back of the stove indicates that the Intrepid has been tested to current UL and ULC standards by CSA. Clearance and installation information is also printed on the label. Local authorities generally will accept the label as evidence that, when the stove is installed according to the information on the label and in this manual, the installation meets codes and can be approved. Codes, however, vary in different areas. Before starting the installation, review your plans with the local building authority. Your local dealer can provide any additional information needed.

For any unresolved questions about installation, refer to the National Fire Protection Association’s publication ANSI/NFPA 211–1988 Standard for Chimneys, Fire- places, Vents and Solid Fuel Burning Appliances. In Canada, the equivalent publication is CSA CAN-B365, Installation Code for Solid Fuel Burning Appliances and Equipment. These standards are the bases for many national codes. They are nationally recognized and are accepted by most local authorities. Your local dealer or your local building official may have a copy of these regulations.

IMPORTANT: FAILURE TO FOLLOW THESE INSTALLATION INSTRUCTIONS MAY RESULT IN A DANGEROUS SITUATION, INCLUDING A CHIMNEY OR HOUSE FIRE. FOLLOW ALL INSTRUCTIONS EXACTLY AND DO NOT ALLOW MAKESHIFT COMPROMISES TO ENDANGER PROPERTY AND

PERSONAL SAFETY.

Chimneys

Your stove must be connected either to a sound masonry chimney that meets local codes, to a relined masonry chimney that meets local codes, or to an approved prefabricated metal chimney. Whichever of those types you use, the chimney and chimney con- nector must be in good condition and kept clean.

If you use an existing masonry chimney, it must be inspected to ensure safe condition before the stove is installed. Your local professional chimney sweep, building inspector, or fire department official will be able to make the inspection or direct you to someone who can.

The chimney should extend at least 3' (914mm) above the highest point where it passes through a roof, and at least 2' (610mm) higher than any portion of a building within 10' (3m).

To assure proper draft and good performance, any chimney used with this stove should extend at least 16' (5 m) above the flue collar of the stove.

0 To 10’

 

2’ Min.

 

3’

0 To 10’

Min.

 

 

2’ Min. 3’

 

Min.

Reference Point

AC617

 

Fig. 2 The 2'-3'-10' Chimney Rule.

Masonry Chimneys

An existing masonry chimney must be inspected to confirm that it has a lining. Do not use an unlined chimney. The chimney also should be examined for cracks, loose mortar, other signs of deterioration, and blockage. Repair any defects before the chimney is used with your stove.

A prefabricated double- wall insulated chimney

A tile-lined masonry chimney

ST241

Fig. 3 Standard Chimney Types

4

30000830

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Intrepid Installation Accessories Table of ContentsIntroduction Specifications Intrepid, ModelChimneys InstallationMasonry Chimneys Chimney Connector Guidelines Prefabricated ChimneysChimney Size Masonry Chimneys, contdDouble-wall Chimney Connectors Single-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsWall Pass-throughs Connection Above the FireplaceRequirements Floor Protection Canadian RequirementsMobile Home Installation Fireplace Hearth ProtectionSafe Ways To Reduce Clearances Clearance to Surrounding Combustible MaterialsWall Shields 25mm Fireplace Clearances Mantel Trim Shields Custom-formed mantel shieldAlcove Installations Construction RequirementsIntrepid 1640 Clearance Chart CornerUnprotected Surfaces Protected Surfaces Rear ExitAssembly Install Stove LegsInstall the Bottom Heat Shield Unpack the StoveInstall Smokeshelf / Firebricks Install the Outside Air AdaptorAttach the Chimney Connector Flue Collar ReversalUse the Air Control Setting that Works Best for You OperationHow the Intrepid Works Burn Only High-Quality WoodStarting and Maintaining a Fire Conditioning Your StoveRefuel While the Embers Are Still Hot Ash Disposal Smoke DetectorsMaintenance Adjust the Door Latch Chimney System CreosoteAnnual Maintenance Draft Management Steel ChimneyInside/Outside Location Flue SizingDraft Testing Single VentingFuel BackpuffingNegative Pressure ConclusionIntrepid NC Woodburning Stove Shell Enamel Parts Intrepid NC Model Suede Classic Green Moonlight Sand Red Blue BrownIntrepid 1640 Woodburning Stove Warranty CFM Specialty Home Products

1640 specifications

Vermont Castings has long been synonymous with quality in the realm of wood stoves, and the Vermont Castings 1640 model exemplifies this reputation with its blend of craftsmanship and modern technology. The 1640 is designed to offer an efficient heating solution while delivering an aesthetically pleasing presence in any home.

One of the standout features of the Vermont Castings 1640 is its substantial heat output. Capable of heating spaces up to 2,000 square feet, this model is ideal for larger rooms or open floor plans. It boasts a heating capacity of 60,000 BTUs, ensuring that your living space remains comfortable even during the coldest winters. With a firebox that can accommodate logs up to 18 inches, this stove is designed for convenience, allowing for longer burn times between refueling.

The Vermont Castings 1640 is constructed with robust cast iron, offering durability and excellent heat retention. The cast iron body not only enhances the stove's lifespan but also helps distribute heat uniformly throughout the room. The aesthetic appeal of the Vermont Castings 1640 is augmented by its classic design, which can seamlessly fit into various home styles, from traditional to contemporary.

Equipped with advanced clean-burning technologies, the 1640 excels in efficiency and environmental responsibility. It features a secondary combustion system that maximizes fuel usage and minimizes emissions, resulting in a lower carbon footprint. The air wash system keeps the glass door clean, providing an unobstructed view of the beautiful flames while reducing maintenance efforts.

Another significant benefit is the adjustable air control system, allowing users to easily regulate the fire and heat output. This feature not only enhances user control but also optimizes fuel efficiency, ensuring that you're not wasting resources. The Vermont Castings 1640 also comes with a sleek and easy-to-operate door mechanism that facilitates loading and unloading of logs.

Overall, the Vermont Castings 1640 is an excellent investment for those looking to add both functionality and charm to their home heating options. Its combination of traditional craftsmanship, modern technology, and user-friendly features make it a standout choice for homeowners seeking reliability and aesthetic appeal in their wood-burning stoves. Whether it's the warm ambience or the heating efficiency, the Vermont Castings 1640 is sure to satisfy the needs of any homeowner looking to enjoy the cozy benefits of a wood stove.
Top Page Image Contents