Vermont Casting 1695CE Assembly, Clean the Griddle Before Use, Set Up the Stove, 2000970

Page 11
Assembly

Vermont Castings Intrepid Multi-Fuel

Assembly

Clean the Griddle Before Use

At the factory we coat the griddle with vegetable oil to prevent rusting while the stove is in transit and storage. Remove the oil with a dry rag or paper towel before you use the stove.

Set Up the Stove

Remove the griddle, front grate bar, the bottom grate, the side bricks, and the ash pan from inside the stove. Place a protective pad on the floor, arrange some sec- tions of 4 x 4 lumber on the pad for support, and care- fully tip the stove back onto them.

Remove and discard the four large slot-head screws from the stove bottom (Fig. 12) and install the stove legs, using the hex head bolts from the parts bag.

Use 11 mm (3/8”) washers with three of the legs; the door/damper handle holder installs in place of a washer on the right front leg. Position the holder so the hole to accept the handle nub faces out from the right side of the stove. Tighten the bolts firmly.

Slotted

 

Screws

 

ST513

Fig. 12

Remove the slotted screws from the stove bottom.

Install the Bottom Heat Shield

To install the bottom heat shield, loosen the leg bolts, and slip the bottom heat shield C-clips onto the bolts. Orient the heat shield so that the longest 273 mm /

10³⁄₄”) edge is at the front of the stove. (Fig. 13) Attach the heat shield to the C-clips with the wing nuts and then tighten the leg bolts.

Storing the Handle

Use the removable handle to open or close the front doors, or to change the position of the damper. After use, remove the handle so it will not get hot, and store it in the handle holder installed behind the right front leg. (Fig. 14)

2000970

10³⁄₄"

9³⁄₄"

ST512

Fig. 13 Attach bottom heat shield.

Door Handle Holder

Clean the Griddle Before Use Bottom Heat Shield

Bracket

Wing Bolt

ST514

Fig. 14 Handle holder and heat shield positions.

Reversing the Flue Collar

You can reverse the flue collar by removing the two screws that attach the collar to the back of the stove, as in Figure 15. Be sure the gasket around the flue collar opening is in position when you screw the collar back on to the stove.

 

Flue Collar Screws

 

ST515

Fig. 15

Reversing the flue collar.

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents The Intrepid Multi-FuelHeaterModel 1695CE InstallationAll of us at CFM Corporation Table of ContentsWelcome Vermont Castings Intrepid Multi-Fuel2000970 SpecificationsIntrepid Multi-Fuel,Model 1695CE, 1696CE, 1697CE Vermont Castings Intrepid Multi-FuelVermont Castings Intrepid Multi-Fuel InstallationOutside Air What Kind of Chimney to UsePrefabricated Chimneys Chimney Connector GuidelinesDouble-wallChimney Connector Masonry ChimneysPrefabricated Chimney Single-wallChimney ConnectorSecuring the Single-wallConnector to a Freestanding Chimney InstallationsWall Pass-Throughs Fireplace Chimney Installations Above a FireplaceFireplace Chimney Installations Through a Fireplace2000970 Floor Protection for Fireplace InstallationsHearths Vermont Castings Intrepid Multi-FuelSummary of Clearances Keep the Stove a Safe Distancefrom Surrounding Materials Clearances2000970 Connecting Flue Pipe - ClearancesVermont Castings Intrepid Multi-Fuel Install the Bottom Heat Shield AssemblyClean the Griddle Before Use Set Up the StovePrimary Air Control OperationAttach the Griddle Handle Intrepid Multi-fuel’sControlsVermont Castings Intrepid Multi-Fuel Glass Door PanelsFront Grate Two Ways to Add FuelVermont Castings Intrepid Multi-Fuel How to Build a Wood Fire and Keep It GoingConditioning Your Stove Intrepid Multi-FuelControl Settings2000970 Refuel While the Embers Are Still HotAsh Disposal Vermont Castings Intrepid Multi-FuelFlue sizing Draft ManagementSteel Chimney Indoor/Outdoor locationNegative Pressure Draft TestingFuel BackpuffingCare of the Cast Iron Surface MaintenanceCleaning the Glass Glass ReplacementReplace the Stove Gaskets as Needed How to Adjust the Door LatchDamper Adjustment Tighten the Damper Handle as Needed2000970 Adjust the Door if NecessaryPermanent Gaskets Vermont Castings Intrepid Multi-FuelVermont Castings Intrepid Multi-Fuel Annual MaintenanceThe Chimney System Creosote2000970 Intrepid Multi-FuelHeaterModel 1695CE Vermont Castings Intrepid Multi-Fuel2000970 Intrepid Multi-FuelHeaterModel 1695CE continued Vermont Castings Intrepid Multi-FuelShell Enamel Parts - Intrepid Multi-Fuel Intrepid Multi-FuelHeaterVermont Castings Intrepid Multi-Fuel Model 1695CE continued2000970 Vermont Castings Intrepid Multi-Fuel2000970 Vermont Castings Intrepid Multi-FuelLimited Catalyst Warranty WarrantyLimited 3 Year Warranty Limited 1 Year WarrantyCFM Corporation
Top Page Image Contents