Sunbeam KY-25 user manual Unpacking Your Product Parts, Technical Specifications

Page 7

SECTION 1 IMPORTANT SAFETY INSTRUCTIONS

1.8 UNPACKING YOUR PRODUCT PARTS

When you get this unit, please transport the product in an upright position only, and place the product on an even surface. Remove the cardboard box without turning it upside down, or laying it on its side.

Please note: If this unit is transported, it must be left in the normal up right position for at least 8 hours before using, to allow the coolant and compressor oil to settle.

a.Remove the adhesive tape on the top of the cardboard box.

b.Open the cardboard box.

c.Remove the Styrofoam packing and angle-protection board.

d.Lift and hold the unit from the Styrofoam packing base by using two people, so as not to tilt the unit.

e.Remove the plastic bag.

f.Wipe it clean if necessary.

g.Then install hot air exhaust duct for condenser side according to the installation instructions.

Keep upright

Figure 2

1.9 TECHNICAL SPECIFICATIONS

 

Model #

KY-25/Y

 

Color

Stainless Steel/White Metal

 

Rate Cooling Capacity

9000 BTU/hr

 

Voltage, Frequency, Phase

AC~115V/60Hz/1 PH

 

Rated Current

8.2A

 

Design Pressure

Max/High 370 psi, Min/Low 150psi

 

Refrigerant, Quantity

R22/500g (17.6oz)

 

Plug Capacity

125V/15A

 

 

Plug Type

5-15P

 

Cord Length

6.43ft/1.96M

 

Dehumidifying Amount

25.4oz/h / 0.75L/hour

 

Air Circulation Volume

5.67CMM/200CFM

 

Net Weight (Unit only)

24.75 kgs/54.56 lbs

 

Dimensions

13.8”L x 14”W x 31.42”H / 35.1cmL x 35.6cmW x 79.8cm H

 

 

 

 

NOTE:

The above data are obtained under the following conditions:

Cooling condition: Dry bulb/Wet bulb: 95°F/83°F (35°C/28.3°C) according to American standard 128-2001.

Operating Limits During Cooling

Maximum condition:

Dry bulb/Wet bulb: 104°F/80°F (40°C/26.7°C)

Minimum condtion:

Dry bulb/Wet bulb: 64.4°F/57.2°F (18°C/14°C)

6

Image 7
Contents Guide D’UTILISATION Table of Contents Save These Instructions for Future Reference Important Safety InstructionsPortable AIR Conditioner Safety Your safety and the safety of others are very importantPlease help us to help you Electrical Requirements Special RecommendationsElectrical Shock Hazard Lcdi Plug Technology US only Recommended Grounding MethodUnpacking Your Product Parts Technical SpecificationsOperating Limits During Cooling Section Section Getting Started AccessoriesTools Needed Knowing Your Portable AIR Conditioner Power Supply Cord and ReceptaclePortable AIR Conditioner Installation Section Installation InstructionsInstalling the Ducts in a WINDOW/SLIDING Door MANUFACTURER’S Recommendation Installing the Ducts in the WallOn/Off Button Use to Start or Stop the unit LCD Display Panel HOW to SETCooling Operation Operating Remote Control Model KY-25Y onlySOFT-DRY Operation FAN-ONLY Operation TIMER-ON Program SettingAuto Operation Draining TIMER-OFF Program SettingWater Full Indication and Draining Water Full IndicationWater Full Indication and Draining CONT’D Storage AT the END of the Cooling Season MaintenanceCleaning or Replacing the AIR Filter External Plastic PartsLOW Cooling Efficiency Section TroubleshootingSet the cooling temperature at a proper level Portable AIR Conditioner does not Work AT ALLNoise and Vibration LOW Cooling CONT’DUnit Turns on and OFF Frequently

KY-25, Y specifications

The Sunbeam Y, KY-25 is a remarkable innovation in the realm of aerosol dispensers, specifically designed for efficiency and user convenience in various applications such as household cleaning, personal care, and industrial use. Combining cutting-edge technology with robust features, the KY-25 represents a significant advancement over traditional aerosol spray technologies.

One of the standout features of the Sunbeam Y, KY-25 is its ergonomic design. The dispenser is crafted to fit comfortably in the user's hand, reducing fatigue during prolonged use. The nozzle is designed for precision, allowing users to apply products evenly and accurately. This results in less waste and enhanced effectiveness in delivering sprays or liquid solutions.

The KY-25 incorporates a unique pressure regulation system that ensures consistent output regardless of the angle or orientation during use. This technology prevents drips and sputtering, providing a smooth and uninterrupted spray. As a result, users can achieve optimal coverage with minimal effort, making it an ideal choice for both commercial and domestic applications.

Another significant characteristic of the Sunbeam Y, KY-25 is its versatility. The device is compatible with various formulations, accommodating a wide range of liquids, from cleaning agents to personal care products. Additionally, the KY-25 is designed for ease of refilling, supporting sustainability by reducing single-use aerosol waste. The user-friendly refill process enables quick and hassle-free transitions between different products.

The KY-25 also boasts advanced safety features. Its design incorporates a child-proof locking mechanism to prevent accidental discharges, making it safer for households with young children. Furthermore, the materials used in its construction are resistant to corrosion and degradation, ensuring longevity and reliability in various environments.

In summary, the Sunbeam Y, KY-25 is a pioneering aerosol dispenser that blends ergonomic design, consistent performance, and versatility. With its advanced pressure regulation system, compatibility with multiple formulations, and enhanced safety features, the KY-25 stands out as a leader in its category. Whether for household chores or industrial tasks, it empowers users with a practical solution for efficient aerosol application. This combination of technology and user-centric design makes the Sunbeam Y, KY-25 a must-have for anyone looking to optimize their aerosol dispensing needs.