Vanguard Heating FB32NCA Installing Fireplace Screen, Tions are included with each accessory

Page 13

INSTALLATION

Continued

INSTALLING FIREPLACE SCREEN

1.Insert each rod through nine rings located at top of screen.

2.Insert first rod into rear hole in left side of firebox. Fasten rod to rear hole near center of firebox using black shoulder screw.

3.Insert other rod into front hole on right side of firebox and fasten using remaining shoulder screw.

Front and

Rear Hole

Screw

Rod

Ring

Screen

Figure 16 - Installing Fireplace Screen

(Shown Without Fireplace Hood for

Clarity)

FIREBOX INSTALLATION USING OPTIONAL ACCESSORY MANTELS

This firebox may be installed using the corner or cabinet mantel with hearth base accessories against a wall in your home. You must use a GA6090 brass trim kit included with the mantel accessories (see Accessories, page 12). Follow the instructions below to install the firebox in this manner.

Note: The instructions below show installation using GM100F/GM101U/GM102W/GM106F/ GM107U series cabinet mantels and the G3000F/ G3001U/G3004W/G3006F/G3007U series hearth base accessories. The hearth base accessory shown is optional for this installation. You can install firebox and cabinet mantel directly on the floor. The corner mantel cannot be installed with the G3000F/G3001U/G3004W/G3006F/G3007U series hearth base. You must install corner and face mantels directly on the floor. If mounting firebox and cabinet mantel to the floor or using corner mantel, an optional G3005 Slim Base kit may be installed.

1.Assemble cabinet mantel, hearth base, brass trim, and trim accessories. Assembly instruc-

tions are included with each accessory.

2.If using an optional GA3700 blower (FB32CA and NLFB32C models only), install a properly grounded, 120 volt three-prong electrical out- let at firebox location if an outlet is not there. If possible, locate outlet so cabinet mantel will cover it when installed (see Figure 18).

3.Install gas piping to firebox location. This instal- lation includes an approved flexible gas line (if allowed by local codes) and a manual shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Connecting to Gas Supply in your log set ownerʼs manual.

NOTICE:Aqualified service per- son must connect firebox to gas supply. Follow all local codes.

4.Place hearth base accessory against wall at instal- lation location. Cut an access hole in hearth top to run flexible gas line to firebox (see Figure 17). Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You can secure base to floor using wood screws. Countersink screw heads and putty over.

5.Route flexible gas line through access hole in hearth base.

6.Center cabinet mantel on hearth base (see Figure 18). Make sure mantel is flush against wall.

Hearth

Rigid

Pipe and

Electrical

Gas Line

Gas Shutoff

Outlet

Access

Base

Valve

 

 

Hole

 

 

 

 

 

 

 

Figure 17 - Placing Hearth Base

Accessory Against Wall

Cabinet Mantel

Figure 18 - Installing Cabinet Mantel

105604-01H

www.desatech.com

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Shown with optional cabinet Unvented VENT-FREE 32 LogMate Universal FireBOXTable of Contents Safety Information Local Codes Product SpecificationsUnpacking Blower Accessory Product FeaturesLocating Firebox OperationProviding Adequate Ventilation AIR for Combustion VentilationFollowing are excerpts from National Fuel Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation AIR InstallationVentilation Air From Inside Building Ventilation Air From OutdoorsMantel Clearances for Built-In Installation Installation ClearancesMinimum 16 inches from Side Wall Conventional Installation of Blower Accessory Installing Blower AccessoryModel FB32CA only Built-In Installation of Blower Accessory Plug in blower power cordOperating the Blower Speed you desireInstalling Fireplace Hood Installing LOG Heater in FireboxRemove four screws holding firebox bottom in place Replace firebox bottom and secure with screwsFirebox Installation Using Optional Accessory Mantels Installing Fireplace ScreenTions are included with each accessory Route flexible gas line through access hole in hearth base27 7/8 BUILT-IN Firebox InstallationTechnical Service Replacement PartsParts Under Warranty Parts not Under WarrantyAccessories Laminate Trim for Hearth or Mantel Hardwood Cabinet Hearth BaseModels FB32NCA and NLFB32NC Illustrated Parts BreakdownParts List Models FB32CA and NLFB32C KEY Part Number FB32CA NLFB32C Description QTY 105604-01H 105604-01H Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Firebox

NLFB32NC, NLFB32C, FB32CA, FB32NCA specifications

The Vanguard Heating NLFB32NC, FB32NCA, FB32CA, and NLFB32C are modern, innovative heating systems crafted to meet the demands of contemporary living spaces. These models emphasize efficiency, reliability, and advanced technology, making them a popular choice for both residential and commercial applications.

One of the standout features of the Vanguard Heating line is its energy efficiency. Designed with cutting-edge technology, these heating units boast optimized heating performance while minimizing energy consumption. With a high energy efficiency rating, they help users reduce their carbon footprint and lower utility bills, providing a substantial return on investment over the years.

These models incorporate advanced heating technologies, including variable speed fans, which adjust according to the heating needs of the space. This feature not only enhances comfort by maintaining a consistent temperature but also reduces noise levels, allowing for a peaceful environment. The intuitive control systems enable users to easily adjust settings, ensuring that their heating preferences are met at all times.

Constructed with durable materials, the Vanguard Heating models are designed to withstand the rigors of daily use. Their robust build quality ensures longevity and reduces the need for frequent maintenance. Additionally, the compact design of these systems allows for flexible installation, making them suitable for a variety of settings, whether in tight spaces or larger areas.

Moreover, the NLFB32NC and its counterparts are equipped with safety features that prioritize user protection. Overheat protection and automatic shut-off mechanisms are standard, ensuring that the units operate safely and efficiently. These heating systems also come with easy-to-read digital displays, enabling users to monitor performance and troubleshoot any issues quickly.

The Vanguard Heating series is also designed with environmental considerations in mind. They comply with stringent environmental standards, contributing to a greener future. The use of sustainable materials in production further reflects Vanguard's commitment to eco-friendly practices.

In summary, the Vanguard Heating NLFB32NC, FB32NCA, FB32CA, and NLFB32C offer a comprehensive heating solution characterized by energy efficiency, advanced heating technologies, durability, and safety features. Their innovative designs cater to a wide range of heating needs, making them an excellent choice for anyone seeking reliable, high-performance heating solutions. By choosing Vanguard Heating, users benefit from enhanced comfort, cost savings, and a reduced environmental impact.
Top Page Image Contents