Empire Comfort Systems VFSV-30-3, VFSV-16-3, VFSV-24-3 Important Safety Information, Death, System

IMPORTANT SAFETY INFORMATION

•An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom

•An unvented room heater having an input rating of more than 10,000 Btu per hour shall not be installed in a bedroom or bathroom.

•Never burn solid fuels in a fireplace where a gas log set is in- stalled.

•Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

•Do not place clothing or other flammable material on or near the appliance.

•Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

•Young children should be carefully supervised when they are in the same room as the appliance.

•This unit complies with ANSI Z21.11.2 Unvented Heaters and it also complies with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.

•Correct installation of logs, proper location of the heater and annual cleaning are necessary to avoid potential problems with sooting. Sooting, resulting from improper installation or opera- tion, can settle on surfaces outside the fireplace.

•Avoid any drafts that could alter burner flame patterns. Do not allow fans to blow directly into the fireplace. Do not place a blower inside burn box area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur as a result of drafts.

•WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns.

•WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.

•Periodic examination and cleaning of the venting system of the solid-fuel burning fireplace, including frequency of such examination and cleaning, by a qualified agency.

•The installation must conform with local codes or, in the ab- sence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA54.

•NOTE: Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compart- ment, burners and circulating air passageways of the appliance be kept clean.

•Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance. Provide ad- equate combustion and ventilation air.

•The flow of combustion and ventilation air MUST NOT be obstructed.

•Provide adequate clearances around air openings into the com- bustion chamber and adequate accessibility clearance for servic- ing and proper operation. NEVER obstruct the front opening of the appliance.

•An unvented room heater intended for installation in a solid-fuel burning fireplace shall comply with the following instructions.

•Afireplace screen must be in place when the appliance is operating and, unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction of combustion air.

•Solid-fuels shall not be burned in a masonry or UL 127 factory- built fireplace in which an unvented room heater is installed.

•Any glass doors shall be fully opened when the appliance is in operation.

•Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at time of appliance installation.

•WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

•WARNING: Before installing in a solid-fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.

WARNING
	CARBON MONOXIDE POISONING MAY LEAD TO
When used without adequate combustion and ventilation air,	DEATH.
heater may give off CARBON MONOXIDE, an odorless,	Early signs of carbon monoxide poisoning resemble the flu,
poisonous gas.	with headache, dizziness and/or nausea. If you have these
	signs, heater may not be working properly. Get fresh air at
Do not install heater until all necessary provisions are made for
	once! Have heater serviced.
combustion and ventilation air. Consult the written instructions
	Some people – pregnant women, persons with heart or lung
provided with the heater for information concerning
	disease, anemia, those under the influence of alcohol, those at
combustion and ventilation air. In the absence of instructions,
	high altitudes – are more affected by carbon monoxide than
refer to the National Fuel Gas Code, ANSI Z223.1, Section
	others.
5.3 or applicable local codes.
	The pilot light safety system senses the depletion of oxygen
This heater is equipped with a PILOT LIGHT SAFETY
	at its location. If this heater is installed in a structure having a
SYSTEM designed to turn off the heater if not enough fresh air
	high vertical dimension, the possibility exists that the oxygen
is available.
	supply at the higher levels will be less than that at the heater. In
DO NOT TAMPER WITH PILOT LIGHT SAFETY
	this type of application, a fan to circulate the structure air will
SYSTEM!	minimize this effect. The use of this fan will also improve the
If heater shuts off, do not relight until you provide fresh air.	comfort level in the structure. When a fan is used to circulate
If heater keeps shutting off, have it serviced. Keep burner and	air, it should be located so that the air flow is not directed at
control compartment clean.	the burner.

18954-0-0705 Page 3